Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Upper Kitchen Cabinet question

Posts

Upper Kitchen Cabinet question

#1

Upper Kitchen Cabinet question

Theresa K

>I'm about to start my kitchen cabinets. I have read that some use 1/2" plywood for the cases, and some use 3/4" plywood. I am planning on making the depth of the uppers 14" with the faceframes.

Is 3/4" thickness overkill for uppers? I would think 1/2" thickness would make installation easier because of the weight difference. But I'm wondering that since I was going a bit deeper in depth, if I should go with 3/4".

Any advice would be appreciated!

Theresa

Re: Upper Kitchen Cabinet question

#2

1/2" ok

John in New Mexico

>I typically use baltic birch, but even in domestic ply 1/2" should be fine. I've seen comercial stuff that was 3/8" particle board, does ok for a while, problems after 10-15 years, though that has more to do with the material than the thickness.

Re: Upper Kitchen Cabinet question

#3

Re: Upper Kitchen Cabinet question

Jim Dillon

>Theresa,

While I used good quality 3/4 inch plywood for both my lower and upper kitchen cabinets, I think now in retrospect that that might have been overkill - at least for the uppers. As long as you use a good quality plywood, appropriate carcass joinery, and glue the back on, you should be fine. Maybe you can split the difference and find some good quality 5/8 thick plywood?? My uppers are 13-1/2 inches wide (including face frame and door) to accommodate the slightly wider dishes we had. Instead of a conventional cleat on the inside to hold the cabinet to the wall, I chose instead to fasten an "L" shaped cleat to rear of the outside top, and also placed a cleat under the cabinet at the rear to support the overall weight. So far, nothing has come crashing down. Having a helper when installing the uppers makes sense and adds a safety factor as the upper cabinets can be awkward to install. Some installers install the lower cabinets first, then use a car jack of some sort to help lift the uppers into place. Good luck.

Jim

Re: Upper Kitchen Cabinet question

#4

Moses Yoder

Re: Upper Kitchen Cabinet question

Moses Yoder

>A question would be what are you doing on the exposed ends? Are you using plain finished ply ends, applying a door on the end, or integrating a raised panel into the end? I typically use 1/2" plywood on unfinished ends and 3/4" ply or raised panels on the exposed ends. On the unfinished ends it helps to set the ends in 1/4" from the edge of the frame so you can scribe the cabinets to fit to the wall and each other.

Re: Upper Kitchen Cabinet question

#5

Re: Upper Kitchen Cabinet question

Fred Davis

>Theresa,

I have been a cabinet maker for longer then I can remember and the standard sheet goods for cabinet carasses was always 3/4" in thickness.

Any attempts to degrade the standard always came from cost cutting measures to keep competitive with job bids.

The standard was and is called out by Architects , the Wood Institute of CA. and conformed to by cabinet shops that wished to keep call backs down to a managable level and or pass preinstallation inspections from unions, the afore mentioned Wood Institute in Ca. and cities and counties using Architect grades and standards coupled with the Uniform Building code.

That being said , I see you have a nice depth to the uppers which if you have not thought about it, would give you a golden opportunity to install your microwave oven in the upper case flush with the face frame.

It looks like magic since the microwave is deeper then the percieved upper case, but if your interested, I can email you a peek of our kitchen I did and how it was done.

FredD

Re: Upper Kitchen Cabinet question

#6

Moses Yoder

Re: Upper Kitchen Cabinet question

Moses Yoder

>I have been a cabinet maker for longer then I can remember and the standard sheet goods for cabinet carasses was always 3/4" in thickness.

"Any attempts to degrade the standard always came from cost cutting measures to keep competitive with job bids.

The standard was and is called out by Architects , the Wood Institute of CA. and conformed to by cabinet shops that wished to keep call backs down to a managable level and or pass preinstallation inspections from unions, the afore mentioned Wood Institute in Ca. and cities and counties using Architect grades and standards coupled with the Uniform Building code."

Are you saying that the standard plywood thickness on face frame cabinetry has to be 3/4" thick in order to pass inspection? Perhaps that is true in California, but I think that is very misleading information. A face frame cabinet with a 3/4" plywood side is not significantly stronger than one with a 1/2" plywood side. We have built hundreds of millions of dollars worth of cabinetry, inlcuding some commercial jobs, using 1/2" plywood on unfinished sides. I still remember when I started working in a wood shop, so I have not been a cabinetmaker longer than I can remember. I started in 1986.

Re: Upper Kitchen Cabinet question

#7

Re: Upper Kitchen Cabinet question

Fred Davis

>Gee Moses , I am impressed no end, "hundreds of millions of dollars worth"

Useing 1/2 " plycore is a signicant saving , just like I said , "cost cutting to stay competitive".

If you would read the post a little more carefully , I am going slow here now, you will note any city or county I contracted in and that was the 5 bay area counties , that used AIA Grades and Standards coupled with the Uniform Building Code and Union and or Wood Institute preinspections required 3/4" sheet goods.

I never said you had to use that particular thickness, there is plenty of low cost , section eight , senior housing type housing being built by under paid assemblers , many of which don't even speak English. Half inch ply with these operations actually would be considered a upgrade.

I started in 1956 , do you remember that year?

FredD

Re: Upper Kitchen Cabinet question

#8

Re: Upper Kitchen Cabinet question

Howard

>I would use 3/4" for the sides, and I use 1/2" for the backs, but that's just how I make them. The 3/4" sides are needed for 35mm hinges if you are going for a frameless cabinet. The weight difference is not that great, especially if you have a helper or use jack supports.