Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

using saw blades as dados

Posts

using saw blades as dados

#1

using saw blades as dados

Quebecnewf

>I am looking into the possibility of ship lapping approx 1200 to 1500 sq ft of 1" boards on my table saw. This will require making a approx a 1/4 by 1/4 dado along both edges of the boards. One on each oposite corner. This is green softwood lumber and I cannot bring myself to use my new expensive dado set to run all this green lumber.

I was thinking about buying approx 4 x 7 1/4 " saw blades and packing them together on the saw and using them as a dado head. These would be just run of the mill framing skil saw blades.

Has anyone done this in this manner and if so what were your thoughts on this. The table saw is a Dewalt Floor model 2 1/2 HP

Quebecnewf

Re: using saw blades as dados

#2

Re: using saw blades as dados

Kneale Brownson Dreaming of the Snow in N. MI

>I shiplapped all the siding for my 28X48 barn using a router. One pass down each side of the pine. I did the first couple of boards with a cheap dado set on the table saw. Router was much easier.

Re: using saw blades as dados

#3

Re: using saw blades as dados

Will Abbott

>Most construction blades have a ATB grind pattern on the teeth. You will not get a smooth bottom dado with this set up. Unless you want to spend a lot of time cleaning up the bottoms, I would use the dado set you have ,or a router. I'm also not sure about the safety of using construction blades this way.

Will.

Re: using saw blades as dados

#4

Re: using saw blades as dados

Charles M

>Quebecnewf,

I think for your saw and the amount of cutting you will be doing it would be better to use a thin kerf rip blade and two passes to cut the rabbets - one pass on edge and one face up.

Charles M

Freud America, Inc.

Re: using saw blades as dados

#5

JL

Re: using saw blades as dados

JL

>I'm not saying you can't do it - just that it isn't advisable. As others have stated, the tooth grinds on most small blades isn't compatible with your application.

If you don't like the router set-up, why not an inexpensive dado set? You can find some cheap ones out there. Another alternative would be Freud's Box Joint Cutter set.

Re: using saw blades as dados

#6

Re: yes - I get a rough dado bottom

Henry (Raleigh NC)

>I have done this, but certainly not in the volume you are suggesting. The bottom of the cut is rough, in part I think because the dimensional tolerances on my $3 blades was poor. As mentioned above, the tooth grind on these blade is not optimal.

However, since I do not have a 'good' dado blade set, this is my only option for rough work; it has served me fine the very few times I used it. For what little i do with it, I could not justify the cost of a real dado set.

Typically, for my 'fine woodworking' I would run two cuts in the TS or use a router.

Henry

Re: using saw blades as dados

#7

Re: using saw blades as dados

steve mackay

>I do it like your describing then clean it up with a #78 or #289.

Re: using saw blades as dados

#8

Re: using saw blades as dados

Paul Rowsell

>I don't mind a rough bottom to the cut. I was thinking a few blades stacked together would be faster and easier on the saw. I know i could do it with one ripping blade and do them flat and then on their edge but this would require 4 passes per board.

A router could do it to but it seems like a lot of work for the router .

Comments

Quebecnewf

Re: using saw blades as dados

#9

Re: I second the router- much easier

Joanne near dansville,ny

>

Re: using saw blades as dados

#10

JL

Re: using saw blades as dados

JL

>A good router (2 1/4 hp) and a good straight bit or rabbeting bit would do a decent job. I've routed many a rabbet on a cabinet back.

This is presuming you have a router table of course. I wouldn't want to free-hand 1500 lf of boards :).

Can you get an inexpensive dado set? I've bought some inexpensive Chinese table saw blades at a "tent sale" and I've seen inexpensive dado sets also. I've also seen inexpensive dado sets at Harbor Freight. I don't know if you have an equivalent where you live.

Re: using saw blades as dados

#11

Re: using saw blades as dados

Fred Davis

>Some thoughts on your job.

Sine it is a straight forward dado job , I would call Nordic Saw and Tool in Turlock , Ca. and have them send a 1/4" Groover.

This a heavy steel disk that carries several carbide chisel teeth and comes in various fractional sizes like your 1/4" for instance.

This tool gives absolutely flat bottom cuts faster and much smoother then a dado set ever could and not near as expensive. Goes right on your saw arbor like your dado set does.

A router approach while slow in comparison does have the advantage of always cutting the same depth thru out the board with having to use hold downs which you need to do with a TS setup.

For me the ideal setup is a TS dedicated to ripping like my older Unisaw with a power feed installed. ;-))

Fredd

FredD

Re: using saw blades as dados

#12

Re: using saw blades as dados

Barry Irby

>It seems to me that quality control is going to be the issue. I have a short attention span and about 1248 feet into and 1500 foot project, I would saw off a finger just to liven things up a little.

Whatever method you use, you have to be sure the rabbets are cut at least full depth both ways. This is easy to do on pieces that are small and easy to handle. On long boards and doing it hundreds of times it becomes an issue.

So, is it easier to set up some saw horses and make a temporary table and lay out the boards and then handle the router, or is it easier to handle the boards and pass them over the saw? Can you set up finger boards or rollers that will assure the boards stay tight to the fence and tight to the table?

Remember, If you have an occasional sloppy one get past you, you won't find them until you are trying to nail them onto the building. You could fix one with the router, but taking it back to the TS might be a problem.

So which is better, applying the tool to the wood, or applying the wood to the tool?