Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Epoxy experts help! Clear finish problem *LINK*

Posts

Epoxy experts help! Clear finish problem *LINK*

#1

Epoxy experts help! Clear finish problem *LINK*

Dave Mount, 28 F this morning

>Hello all--

I have a run of four canoe paddles in progress. My plan was to glass the blade faces with 2 oz glass. Last night I did the first one and it's as though the fabric did not fully wet with epoxy resin -- it didn't just disappear like I'm accustomed to. The cloth was dry laid and wet from above, I squeegeed it lightly, just enought to spread the epoxy and get it to penetrate to the wood. It did that fine, but the fabric is still clearly visible. I'm not talking about the surface texture, I'm talking about being able to see the cloth and the weave down in the epoxy.

Last night I thought it was perhaps because my resin was old so I bought fresh today and did a test patch (not on a paddle) and had the same result. I also tried applying more resin and trying to work it into the fabric more, but that does not help. I also tried heating it with a hair drier and that didn't help either. There are no actual "bubbles" under the fabric, but it's like there's a tiny amount of residual air down in the fabric that won't come out so the fabric becomes clear. This is not a generalized fog or blush, the resin itself is crystal clear -- the problem is specifically in the cloth.

Any ideas? I'm using West Systems 105 resin and 207 hardener. The shop is at 60 degrees which is at the bottom of (but within) the recommended temperature range. The cloth I'm using is 2 oz cloth (presumably E glass, though it's not marked as such) distributed by Hobbico, I've give a link to it below. These are cherry paddles and having them nicely finished is important to their intended audience.

Long as I'm asking, do you think 2 oz glass is too much for this app? I have some 3/4 oz also. . .

Any help appreciated,

Dave


Hobbico 2 oz glass

Re: Epoxy experts help! Clear finish problem *LINK*

#2

Re: Epoxy experts help! Clear finish problem *LINK*

Mark Rakestraw

>Your epoxy brand is reputable, your glass source is suspect. No where on their website that I could see did they advertise "wets out clear", and certainly not all glass does. I've had good luck with Raka (link below) for both glass and epoxy. I've used both 2 oz and .75 oz glass on paddles with good luck. Usually I only do the bottom 4 inches or so of the blade however to keep the weight down.

good luck,

Mark


Epoxy and glass source

Re: Epoxy experts help! Clear finish problem *LINK*

#3

Re: Thanks, will try that

Dave Mount

>Thanks Mark, I called Raka this morning and they're going to ship me some glass overnight and we'll see how that goes. Though my experience is not extensive, I'd never experienced cloth that didn't wet out clear. Too bad I had to learn that lesson on a finished paddle instead of a scrap. . .there's some sanding in my future.

Best,

Dave

Re: Epoxy experts help! Clear finish problem *LINK*

#4

Re: Thanks, will try that

Alan in Little Washington (NC)

>Sounds to me like your glass was wet or damp. I have done a lot of glass work with epoxy and polyester and only had a problem like you describe when I had some damp glass cloth.

Re: Epoxy experts help! Clear finish problem *LINK*

#5

Re: Seems unlikely in this case

Dave Mount, 28 F this morning

>Thanks for the suggestion, but moisture seeems extremely unlikely in this particular case. The cloth was out of the package and in the shop for a couple days before using, and my shop is only at about 50% humidity right now (separate building). Good to know to watch for that though.

Best,

Dave