Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Router table plates??

Posts

Router table plates??

#1

Router table plates??

Rob Stokes in North Vancouver

>I get to build a new router table into my new (to me) cabinet saw. My last saw had the Rockler table insert plate and it was OK, except the inserts screwed in. Curious what everyone's plate du jour is these days?

I'd like a fancy lift - but the $$ isn't there for one.

Rob

Re: Router table plates??

#2

Re: Router table plates??

del schisler

>here are some plates I have the router table and lot's of other item's This a good place for router stuff

http://us.oak-park.com/catalogue.html?list=BP--

Re: Router table plates??

#3

Re: Router table plates??

Richard Jones

>Well, my $.02..........

I got a brand X plate (one of the leading brands), after someone gave me a gift certificate to Woodcraft, thought it would be a nice addition to my new TS wing router table. This was a mailorder..........

Plate is "guaranteed" to be within .007 of flat, but mine was something like .042, which shows a definite crown. (And yes, that is W-A-Y too much for the weight of the router to pull down). I have e-mailed the company numerous times, but they wouldn't make it good, so, with that said.............

If you do indeed buy one, make sure that you go and pick it up in person, armed with your trusty straightedge and some feeler gauges and do some shopping for the one with the least runout. Mine works OK, but only because my router fence is a piece of 3 1/2" aluminum channel and it pulls the plate flat anyway.

If I sound bitter about the experience, it's only because I am........

Anyway, the plates are a nice feature, especially with the replaceable/removeable inserts, but I wish I had just gotten a nice piece of aluminum plate and made my own.

Rich in VA

Re: Router table plates??

#4

Re: Router table plates??

Chuck in ND

>I bought a Woodpeckers 3/8" thick aluminum router plate and ring set last year when I built a benchtop router table and couldn't be happier. The rings twist lock into place.


img

Re: Router table plates??

#5

Re: Router table plates

Mark Mandell - Gone Round In Jersey

>I use a 3/8" phenolitic plate in my table-mounted setup. I have a set screw adjuster at each cornet to match a steel nail head in the table lip. I make my own inserts from 1/4" plexi to fit the bits. It's stayed nice and flat over a bunch of years. Taint fancy or calibrated, etc., but it get the job done.

mm

Re: Router table plates??

#6

Re: Compatibility issue w/Router table plates??

George@Colonel's Workshop-Havertown PA

>Good Afternoon Rob,

I've had a couple router table plates with pop in inserts. My last one was a Rousseau. I was satisfied with all of them. The opening in my router table top was created for the Rousseau. The top is maple bowling alley stock and is 1 1/2" thick. After years of eating gruel and drinking tepid water, I finally had enough put aside for a JessEm Mast-R-Lift. The plate is of a different size than the table opening. I had to shrink the opening in one dimension while expanding in the opposite. It came out okay functionally, but its not pretty like it was before the lift.

If there is a chance you will eventually acquire a lifting devise, I suggest you make your opening compatible with or smaller than the lift plate. Make your own short term router plate.

George

Re: Router table plates??

#7

Re: Router table plates??

Bob Entwisle in NJ

>I've had the woodpeckers phenolic plate for about 3 years now with a Hitachi MV12 hung on it and it's stayed flat etc. It has the screw mounted rings and they are a bit of a pain to change. I think the twist lock rings would be a good addition. Woodpecker also sells a template for cutting the mounting hole for the plate, it�s just a big hunk of MDF, but I think it was only 10 bucks and made the job of cutting the hole for the plate simple. Well worth the 10 bucks.

Re: Router table plates??

#8

Woodpecker/Woodcraft Pinnacle

Craig Daymon

>Woodpecker is making the Pinnacle inserts for Woodcraft or you can get it with the Woodpecker name direct. I have the benchdog insert, the rockler, the wooodhaven and the woodpecker (long story) and the woodpecker is far and away the best of the lot. I have the aluminum one with one additional insert. (It comes with 2 or 3.) Solid, won't ever sag and the inserts fit in real secure and level.

-Craig

Re: Router table plates??

#9

New e-mail, previous message has wrong address.

Craig Daymon

>