Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

10" saw blades

Posts

10" saw blades

#1

10" saw blades

iew

>I know, I know search first. I need a new blade for my Jet cabinet saw. I have have been using a WWll for years and it is finally wearing out. I need some suggestions for a new blade. I have the thin kerf and it has been great. No one was selling blades at the Arlington show last December.

Re: 10" saw blades

#2

Re: 10" saw blades

Lee Schierer - McKean, PA

>I've been very happy with my Freud blades. You can easily get two for the price of on WWII.

Lee

Re: 10" saw blades

#3

Re: 10" saw blades

Thomas Skaggs, Foothills of Mount Level

>Have you sent the WWII back for sharpening? If not, then that's the thing to do.

But if indeed you need a new blade and you have been happy with the WWII then why change horses? The WWII blade is still a great blade.

Tom

Re: 10" saw blades

#4

What are your requirements?

Bill Tindall, E.TN

>I will take the opportunity of your question to explore some blade selection factors.

Requirements- do you mind changing blades to specifically suit a task or do you want one blade that does it all? How thick is the stuff you cut? How finished a cut do you require. How much are you willing to pay to get some improvement in smoothness of cut?

Factors

Safety: I leave a fine tooth 7.1/2 or 8" blade on my 10" saw and only change it for special cutting situations. This blade cuts up to 6/4 stock fine and the saw marks are removed with a swish of a hand plane or light jointer pass. There is virtually no grabbyness with this kind of blade so it doesn't throw things or offer much of any cutting resistance. Hence, great control, expecially for small parts or thin stock.

Smoothness of cut: It seems that many buy solely on how smooth the saw cuts, absence of tooth marks. If you joint after cutting, having a blade that rips glue joints is of no practical value, and there are disadvantages with such a blade. Hence, any name brand blade will do for routine cutting. If the company stays in business they obviously make blades that work. So pick for convenience in buying and price.

Time between sharpening: A blade with some side relief (set) will stay sharp longer and not gum up, but such a blade may leave some evidence of teeth marks.

Versatility: A combination blade is a good choice if you don't like changing blades. If you cut a lot of miters you may want a cross cut blade for this task. But don't attempt to rip with a cross cut blade. They may throw things on a rip cut. If you do a lot of ripping of thick stock your saw will enjoy a coarse rip blade that loads the motor less.

No doubt there are other factors. I used to fret over blade selection and the older I get the less important I consider such things.

Re: 10" saw blades

#5

Re: 10" saw blades

George@Colonel's Workshop-Havertown PA

>I noticed Tommy,

That they offer a version of the WWII with a flat raker tooth. I wish I had one among all of the ATBs I have in my Leitz, Freuds, and Forrest.

George

Re: 10" saw blades

#6

Re: 10" saw blades

Mark Mandell - Gone Round In Jersey

>Quick way to improve your cut quality is to go to a full kerf blade. Thin kerf is designed for saws with less juice. You cabinet saw has power to spare to run a full kerf cut. I regard that stuff about thin kerfs saving wood to be puff; a 64th of an inch is meaningless.

The WWII comes in a full kerf, so if you like that blade stay with it.

My workhorse blade is a Systematic glue-line rip. I'll switch to a coated 80t Freud Ultra fine for cross cuts and the few miters I do on the table saw. I also use a Jesada 50t Maxi-combo (same as the CMT) when working with sheet stock. I have the same saw.

Re: 10" saw blades

#7

Re: 10" saw blades

iew

>I have been cutting a lot of sheet stock lately.

Do some miters.

Use my Dubby more than my mitre saw.

Smooth cut is important to me.

Do very little ripping.

Re: 10" saw blades

#8

Re: Sheet Rock!!!

Mark Mandell - Gone Round In Jersey

>On a table saw? Yeow! What a mess! Abrasive as well.

I've hung a lot of rock, but it's all been "score and snap" with the rare jabsaw cut for notches and such.

Go to a full kerf WWI and use a utility knife with an SR square on that rock. |;-}}}

Re: 10" saw blades

#9

Re: Sheet Rock!!!

Glenn Madsen, SF Bay Area

>Uhhh, Mark. Read that again.

Sheet STOCK.

Not the same. ;-)

Re: 10" saw blades

#10

Re: ROFLMAO

Mark Mandell - Gone Round In Jersey

>Duhhhhhhhhhhhhhhhhhhhhhhhh

|;-}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}}

[don't think the utility knife will work after all]

Re: 10" saw blades

#11

That's why I always prefer the term "drywall"

Dan Mitchell

>No such confusion.

Plus, it's MUCH easier on the table saw than sheetrock! ;-)

Seriously, I've always wondered, is the term difference mostly a regional thing? Seems like when I was in Ohio it was all "drywall". Here in Washington, it seems to be mostly "sheetrock", though I haven't had occasion to use either term as much lately.

I believe "sheetrock" is actually a bit like "Kleenex", right?

In that it's a brand name, that is...

Dan

Re: 10" saw blades

#12

Jason Roehl in Lafayette, IN

Correct.

Jason Roehl in Lafayette, IN

>Sheetrock is made by USG, I think. "Drywall" is usually a layman's term, but quite common, and the industry term would be gypsum board.

Jason (painted WAY too much of the stuff...)

Re: 10" saw blades

#13

Re: Sheet Rock!!!

iew

>Who said anything about sheetrock! I said sheet goods! You know, 4x8 plywood, stuff like that.

Re: 10" saw blades

#14

Re: Sheet, uh, something

Mark Mandell - Gone Round In Jersey

>Past time for new glasses. Hopefully the new ones won't make my eyes cross!!

|;-}

Re: 10" saw blades

#15

Dale Lenz

Re: Sheet, uh, something

Dale Lenz

>I'm glad I'm not the only one around here that miss reads a post. My brian said sheet rock also, clearly a cross fire, : ' >.

Re: 10" saw blades

#16

More coffee

Lee Schierer - McKean, PA

>"My brian said sheet rock also, clearly a cross fire, : ' >"

Looks like you need at least one more cup of coffee to get your brain hitting on all cylinders.... ;)

Lee

Re: 10" saw blades

#17

I Feel Much Beder Now

Mark Mandell - Gone Round In Jersey

>Knowing I'm not along and someone else has a keyborb like mine.

Re: 10" saw blades

#18

Re: I Feel Much Beder Now

iew

>Mark:

Look what you have doen to my post. Completely mangeled it. All I wanted was a blade rekomendaten. Now I have a primer on SHEET ROCK!;)

Re: 10" saw blades

#19

Re: Mangled?

Mark Mandell - Gone Round In Jersey

>Jeez, a little dyslexsia and suddenly I'm perzzona mom grada.

So, anyway, what'd you buy?

|;-}}

Re: 10" saw blades

#20

More Like,

George@Colonel's Workshop-Havertown PA

>Mark got "plastered" in lieu of sheet rock. :<)

George

Re: 10" saw blades

#21

Re: More Like,

iew

>Maybe taped and bedded!;)

Boy this easy!

Por Mark, he was born with a trowell in his mouth!

Re: 10" saw blades

#22

Shall We Finish With Tung in Cheek?

George@Colonel's Workshop-Havertown PA

>

Re: 10" saw blades

#23

Your opening statement about using a WW11........

Art Silva

>for years should be all the recommendation for buying another one. I have been using them for over 35 years, and I have not yet found a reason to change, and I have always sent them home to Mama for sharpening, which they require less frequently than other brands. Keeping your Forrest blades super clean is the secret to their long cutting life.

As my Sainted Mother used to say: "Going first class costs so little extra, and it does wonders for your ego!"

Re: 10" saw blades

#24

Re: Who's Brian?

Al Stokka - Cambridge, Iowa

>...and who asked for his opinion? ;^)

Al