Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

My New Shop-Electrical Question

Posts

My New Shop-Electrical Question

#1

My New Shop-Electrical Question

Howard

>My shop is coming along, could someone help with electrical outlet height question - the structure is a 2 car garage 25' x 25'. my understanding is there is no NEC requirement for box height. To clear benches, etc., I was thinking of 36", but I would appreciate all opinions. Also, could someone help with how to post pictures, which I would love to do.

thanks,

howard

Re: My New Shop-Electrical Question

#2

Re: My New Shop-Electrical Question

woodenleg

>In my state all boxes have to be 4' from the floor. They all have to be GFI protected, unless it a single line for specific use. Check with your building codes folks.

Dave

Re: My New Shop-Electrical Question

#3

Re: My New Shop-Electrical Question

Henry Higginbotham

>I put mine at 16" and 58�" (floor to center of box), and have been happy with that. It's not much more trouble or expense to put two boxes in the same stud bay, and it greatly increases the chance that you'll actually be able to get to one after all the junk accumulates. Put in more than you think you'll ever need, use good quality devices, do it to code, and then you can be "done" with it.

Re: My New Shop-Electrical Question

#4

JL

Re: My New Shop-Electrical Question

JL

>On my flat wall, I put my "boxes" so that the lower edge of the receptacle cover is at about 49". That way I can lean a piece of plywood on the wall without covering the outlet.

They are at about 50" on the walls with benches.

Re: My New Shop-Electrical Question

#5

Re: My New Shop-Electrical Question

Dan Donaldson

>As stated, be sure to check the local codes. A garage has special requirements.

Re: My New Shop-Electrical Question

#6

Re: My New Shop-Electrical Question

Larry Clinton At Frankfort (Central)., Indiana

>Howard, I installed most of my boxes about 52" off the floor. That way you can install (& move) benches along any wall. It also allows you to put a 4' piece of plywood against the wall without covering the outlet. I purchased a full carton of outlet boxes (100) & used them all plus. I did go with the cheaper receptacles as those are quite easy to change later if needed. I installed an outlet on every other stud (studs on on 16" center), I also installed extras where I thought I might want one - near the doors etc. I put 3 rows of outlet on the ceiling about 4' apart for my shop lights (and a few extra). Each row on the ceiling is on a separate switch - controlling 8 or so twin florescent light fixtures. I also installed another switch to 6 boxes on the ceiling and installed halogen bulbs in those. I installed one 60 amp 240 V outlet for my large welder. I also installed several 30 amp 240 outlets on the walls, one for the compressor, dust collector, and Unisaw. I really didn't think I would need more but as I was finishing the shop in drywall, I went ahead and added another 5 or 6 along the walls. It was really a great thing that I did as I now have a lot of 240 equipment including my new Planer, Joiner, Surface grinder, and band saw. I have the largest 100 amp entrance I could find and have every breaker slot used. It is sure a lot cheaper and a whole lot easier to install an extra 10 outlets now, than have to tear out a wall to install one later. Here in Indiana all Garage outlets have to be protected by a GFI. You can use GFI breakers but it is cheaper to just install a GFI outlet as the first of the string. I sure don't regret the extra money and time I spent installing all the extra outlets. If I had it to do over, I would probably have added another 5 or 10. I used #12 wire on all 120V circuits and #10 on all 240V (except the welder). That allowed me to use 20 amp breakers on the 120V and 30 on the 240V.

Re: My New Shop-Electrical Question

#7

Re: My New Shop-Electrical Question

steve mackay

>I installed mine at 4'. I used two gang boxes for the outlet and the " light switch " that turns on / off the dust collector so the switch was easy to reach. Plus it hits the average height of my machines when mounted on legs / stands so I could bundle up the cords and not have them hang'n. The GFI is where I can see it and reset. I can just glance at the plug over the machine when "trouble-shooting" and not bending over and around to make sure Dummy had it plugged in all the way !

Re: My New Shop-Electrical Question

#8

Thanks for the help..............

Howard

>I will check with my building dept before going to work, and I will make sure to put in enough. Thanks again.