Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

finishes for zebrawood

Posts

finishes for zebrawood

#1

finishes for zebrawood

Ron Detz

>I am making kitchen countertops out of zebrawood. anyone have advice on finishes, or experience with this wood?

Re: finishes for zebrawood

#2

Re: finishes for zebrawood

Sgian Dubh

>Crown cut shows yellow/red/orange and black blotching. In radially sawn wood the stripiness is due to alternating spiral grain, and the blotchiness in crown or radially cut material is due to the same growth pattern.

Okay to work in the solid, but you'll usually get tearout with every other stripe whichever way you feed it through machines. Often best taken to final dimension with thickness sanders, and usually best prepared for polishing using the following, or a mix of the following: power sanding, hand sanding and scraping.

As you work it, particularly with sanding machines, it smells pretty bad. Remove splinters immediately as they rapidly fester and balloon up, or at least they do with me.

Zebrawood seems a particularly strange choice for a kitchen countertop to me. Well, any solid wood seems a strange choice for this purpose in my eyes as it'll get a beating. I know people do it, and most go for an oil or water based varnish finish. They all seem to end up looking tatty in fairly short time scales, ie, a year to two years. Slainte.

Re: finishes for zebrawood

#3

Ellis Walentine

What Sgian said

Ellis Walentine

>I am one of those brave souls who is making wooden countertops as we speak. I've had them before and made them for customers in the old days. As Sgian mentioned, a solid varnish finish is probably your best combination of moisture and wear resistance. I'm using Minwax Helmsman spar urethane on my maple counters. In the past I have used Waterlox and it protects nicely against moisture and discoloration, but it isn't abrasion-resistant enough to hold up as well as a harder varnish to the constant abuse of food preparation.

Another note: One of the most important things you can do when making a wooden counter is to seal the edges of the sink cutout and the area over, under and around the sink area. I use boatbuilder's epoxy for this, making sure to get a thick continuous film. Also, be sure your sink opening leaves enough room for the top to contract during heating season. Otherwise, the wood can split, and as soon as moisture gets in there, your top is on the road to ruin.

Re: finishes for zebrawood

#4

Alan Young

Ellis- It would be great to see some

Alan Young

>picture documentation of your counter tops. Some of us may want to try this road less traveled...

Alan

Re: finishes for zebrawood

#5

Ellis Walentine

Yeah, I should have...

Ellis Walentine

>... been taking pictures, I guess, but as I found out in my magazine days, photographing a project while you build it just about doubles the amount of time it takes. I'm between coats of finish right now Alan, but I will take a few shots after the next coat and maybe show how I plan to assemble the parts.

Ellis

Re: finishes for zebrawood

#6

Ellis Walentine

Two roads diverged ...

Ellis Walentine

>

Sorry for the oblique reference to "The Road Less Traveled," Alan. That's one of the few poems I can recite by heart, a reminder of my years in New Hampshire.

Here are a couple shots of my countertop in process. I'm building an L-shaped counter about 12' long with a 6' return. The sink will be in the long leg (on the left) and the stove in the short one. The two pieces meet at a miter that will be assembled on the job. The miter has a continuous spline joining the pieces, with three countertop bolts pulling the two together. I will use a thin bead of dark caulk in the joint shoulder when I assemble it on the premises. It will squeeze out and leave a solid impregnable barrier to keep water from leaching into the joint. The joint itself was primed with a couple coats of diluted varnish.




Miters are tricky because, if you want to keep them tight, you need to allow for the tops to move relative to the base cabinets. As humidity increases, the outside of the miter will open; and, as it decreases, the gap will appear at the inside of the corner. The trick is to design a top that can expand and contract that small amount without restraint, which might exert too strong forces on the wood and split it. The ticket is to secure the top near the inside corner and make sure the rest of the connections to the cabinetry allow enough movement of the top between the corner and the ends.

The point I made about sealing the endgrain is critical. I used West System epoxy, although other good boatbuilding epoxies should be fine. Epoxy the endgrain before finishing the work surfaces. If you slop extra epoxy over the edges of the opening, you can remove the excess with a sharp chisel.

I'll try to grab a shot of the cabinet-connector arrangement next time I go out there.

...Ellis Walentine, Host

Re: finishes for zebrawood

#7

Alan Young

Thanks for those pictures Ellis...

Alan Young

>and the descriptions. My wife is talking about wood counter tops in our kitchen. That is some amazing Maple!

Alan

Re: finishes for zebrawood

#8

counter intuitive

Michael Dresdner

>I rather like zebra wood and used it extensively when I was in the guitar business. As for a counter top finish, I would suggest a good quality interior oil based polyurethane. There is no real advantage to using exterior or spar urethanes, and there is some disadvantage.

Re: finishes for zebrawood

#9

Check out...

Clint Searl, at the base of Haycock Mtn

>A one part clear water borne epoxy like Behr garage floor finish. It's easy to apply, water white, and tough. I used it on a wood sign that's been exposed to the weather for over 4 years, and there's no indication of deterioration. I also used it on the top of my shop storase cabinet, which is red oak T&G flooring. It's also a great sealer/finish for porous tile. Two coats on anything for a bullet proof finish.

Clint