Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Pocket Hole Screws in Ipe

Posts

Pocket Hole Screws in Ipe

#1

Bart Goldberg

Pocket Hole Screws in Ipe

Bart Goldberg

>Hi All,

I'm making an outdoor table from Ipe using Pocket hole screws. I tried screwing together some scrap apron to leg sections and noticed that the screw caused the undrilled leg to split. Is there any way to prevent this - I can't figure out how to pre-drill the hole in the mating pieces prior to assembly.

Thanks

Bart

Re: Pocket Hole Screws in Ipe

#2

Moses Yoder

Re: Pocket Hole Screws in Ipe

Moses Yoder

>Are you using a Kreg screw? They are cut like a self tapping screw at the tip to avoid splitting the wood. I have noticed this on a few pieces of hard wood where the screw enters close to the end also. Try putting a screw in just far enough to mark the hole then removing the apron and pre-drill the right size hole. The other option, if you have the room, is to keep the screws further away from the end of the leg.

Re: Pocket Hole Screws in Ipe

#3

Re: Pocket Hole Screws in Ipe

ken raddon

>I've had them split the end of the wood but it was always because I was going in at the wrong angle. Make sure the screw is not headed towards the end of the receiving piece.

Re: Pocket Hole Screws in Ipe

#4

Ellis Walentine

Re: Pocket Hole Screws in Ipe

Ellis Walentine

>Ipe is notorious for splitting. You need to drill a pilot hole that is close to the O.D. of the screw threads and use those self-tapping stainless-steel screws sold for decking. Only experimentation will tell you what size hole to drill.

Ellis

Re: Pocket Hole Screws in Ipe

#5

Bart Goldberg

Re: Pocket Hole Screws in Ipe

Bart Goldberg

>Hi Moses,

Thanks for the advice - I was using some of Kreg's weather resistant 1 1/4" screws - but they are course thread. I called Kreg and they recommend that I switch to their Stainless Steel fine thread screws. So, I just ordered some from Amazon. In the meantime, I'll try some of my regular fine thread screws into some scrap to see if that makes a difference. Else I'll be trying your pre-drill method.

Thanks

Bart

Re: Pocket Hole Screws in Ipe

#6

Bart Goldberg

Re: Pocket Hole Screws in Ipe

Bart Goldberg

>Hi Ellis,

Do they sell these self tapping SS screws at HD?

Thanks

Bart

Re: Pocket Hole Screws in Ipe

#7

Re: Pocket Hole Screws in Ipe

Glenn Madsen, SF Bay Area

>I've purchased them at what I consider a 'real lumber yard'. In bulk, buy them by the pound.

Re: Pocket Hole Screws in Ipe

#8

Re: Pocket Hole Screws in Ipe *LINK*

George (Oxford, NC)

>I would use McFeeley's. The description says they are for Ipe.

George


Mcfeely's SS Pocket Screws

Re: Pocket Hole Screws in Ipe

#9

Ellis Walentine

I bought them at Sierra Supply

Ellis Walentine

>...which is in Hatfield, PA, right up from the big 5-points intersection. They specialize in decking. The ones I used were about a #8, with a typical flat head and Robertson (square) drive. I don't know if they are big or long enough to screw your table legs and apron together.

I looked at the McFeely's screws that George recommended and they look like they would be fine for this, if they're long enough.

Ellis