Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Removing drill chuck help

Posts

Removing drill chuck help

#1

Removing drill chuck help

jeff

>Hi all

I tried to remove the chuck from a Makita 1/2" drill.

I've removed the internal screw, grabbed the shaft with a wrench, installed a large allen head wrench into the jaws and tried to unscrew the chuck.

I've tried soaking in penetrating oil, heat, cold, hammer, everything I can think of, but this chuck won't budge.

I tried turning both ways to break it loose (It should unscrew counter clockwise like all my others), nothing, nada.

Any other ideas tricks?

Jeff

Re: Removing drill chuck help

#2

Re: Removing drill chuck help

Barry Irby

>Not sure from your post, but was one of the "everythings" you tried hitting the Allen wrench with a hammer? Install the short end of the largest one you have that will fit in the chuck and hit the long end a sharp blow with a hammer. Of Course in the direction that would unscrew the chuck. Home made impact wrench.

If none of those things work, maybe you could find someone with an impact wrench and have them use that.

Re: Removing drill chuck help

#3

Re: Removing drill chuck help

Curly Smith

>Are you sure you're turning it in the proper direction? With the drill facing you, are you turning the allen wrench counterclockwise to remove the chuck?

Are you sure it's not a taper-fit chuck?

Re: Removing drill chuck help

#4

Re: Removing drill chuck help

Will Abbott

>Most drill chucks have left hand thread screws holding the chuck in place. that means righty loosey,lefty tighty

Re: Removing drill chuck help

#5

Jim DeLaney, Austintown, Ohio

Re: Removing drill chuck help

Jim DeLaney, Austintown, Ohio

>NO, they don't.

The retaining screw in the center of the shaft is left-threaded, but the chuck itself is plain old 3/8" RIGHT-HAND-threaded.

Re: Removing drill chuck help

#6

Re: Removing drill chuck help

Gene Gauss

>A big hammer hitting a big Allen wrench clamped tightly in the chuck has always worked for me (counter clockwise).

Re: Removing drill chuck help

#7

Re: what I did.

jeff

>Hi all

I've had no trouble removing chucks before.

I hit this chuck with everything I had.

I first removed the hold in screw, it came out real easy (and was reverse thread).

Then tried to unscrew the chuck counter-clockwise (the normal way).

Then put in the chuck key and hit it with a mallet.

Then tried in reverse (in case it was a strange one).

Then tried again in normal way.

Then tried the Allen key trick with all directions,

Then tried a impact wrench.

Then soaked it with Liquid Wrench overnite.

Then tried the inpact wrench again.

Finally tried heating it with a heat gun.

Finally gave up and dropped a note here on the forum.

I did have a thin wrench on the threaded shaft to prevent it from turning.

This is one tough cookie!!!!

Jeff

Re: Removing drill chuck help

#8

Rick L

Re: Advanced options...

Rick L

>If the chuck is totally shot, cut it off with an abrasive wheel on a Dremel or angle grinder. I have an impact tool and that makes short work ot the task. An Oxy-acetylene torch will work but you have to work fast or you will melt the plastic. My job is repairing tools so I've tried it all.

Re: Removing drill chuck help

#9

Re: what I did.

Curly Smith

>OK, how about this:

Get a LH threaded bolt the same size as the chuck screw and use it to hold the shaft. Tighten the bolt and hold it in a vise. Use a pipe wrench to free the chuck. Once the chuck is free, apply thread compound and re-install the chuck. Then hold the chuck and remove the bolt. Finally, remove the chuck body as normal.

Have you run the drill since you started just to make sure it still sounds OK? I'd be concerned about the gears and bearings.

Re: Removing drill chuck help

#10

Re: what I did.

jeff

>Curly

Good idea, I'll try it.

Actually, the drill is toast. But I have a real good Jacobs chuck on it that I want to put on another drill that has a junk chuck.

PS: My new jointer mobile base is finished. Looks and works great.

Now I finally know how to figure strength.

Thank you for your help.

Jeff