Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

I'm a gona do some wood working but

Posts

I'm a gona do some wood working but

#1

I'm a gona do some wood working but

Dustmaker Mike

>I am not sure how thin to cut the Maple. OK I am going to make a hall table and I want to bend some big leaf maple. I want the apron to be 3/4" thick when I am done bending it. I don't have a way to steam bend it so this will be a dry bend. I am going to build a form to bend it against. Now the trick is I want to do a double bend. A large radius in front into a tighter radius where it will met the back apron. The design is sort of like a Denilun table with the back side of the apron being bent again at a sharper bend. I wish I had a picture of it but I don't it is in my head (and that is a scary place to be). So how thin should the maple be cut into strips to make a ~12 radius bend? The length of the table will be ~38" to 40" and the depth will be about ~16"

Re: I'm a gona do some wood working but

#2

Re: I'm a gona do some wood working but

Bruce, a MN Galoot

>For something with a tight radius like that I tend to stick with laminations less than 1/8". Maples is very flexible in thin dimensions.

A bunch of years ago, I ordered the parts to make an archery bow - fiberglass and maple, up to 1/8" thick plus epoxy. They were frightfully late in being delivered so I called the company. He checked his records and found that UPS had left the box on my deck a week before. I went and found the box - that was the key. I was expecting something 6' long, but instead, everything was coiled into a little box only about 16" in diameter.

I also have found that the more laminations you have, the less springback you will experience when you take the glued blank from the form. I generally shoot for at least six laminations. So in your case 6 1/8" strips will make a 3/4" final piece.

Bruce

Re: I'm a gona do some wood working but

#3

Jim DeLaney, Austintown, Ohio

Re: I'm a gona do some wood working but

Jim DeLaney, Austintown, Ohio

>Mike,

For that large a radius, I'd use strips about 1/8" thick. Maple bends very nicely, and easily, so you shouldn't have any problems at all.

What glue are you using? I've had really good results using plastic resin glue. Titebond (PVA) will sometimes creep a bit on laminations, and also has a greater tendency to show between lams in the finished project. You could always use hot hide glue, or Old Brown Glue. Both work very well for laminating.

Jim D.

Re: I'm a gona do some wood working but

#4

Re: I'm a gona do some wood working but

Thomas Skaggs

>I agree with Jim. You might be able to do it with 3/16" thick but 1/8" should do it. In addition to the adhesives listed by Jim you could also consider Titebond's Cold Press Veneer adhesive.

Tom

Re: I'm a gona do some wood working but

#5

Thanks guys I didn't think

Dustmaker Mike

>of what type of glue to use. Now I will have to run to the store and force myself to buy some.

Thanks wish me luck

Re: I'm a gona do some wood working but

#6

thickness to use

Bill Tindall, E.TN

>The plant stand I posted earlier is done with 1/8" strips, 6 of them. There was no spring back. It took a stout clamp to force the bend at the tightest spot.

Do not underestimate the difficulty of getting the glue on, and the assembly in the clamps, and applying pressure to squeeze the excess glue out before the glue gets to thick to squeeze out.