Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Saw Blade Stabilizer

Posts

Saw Blade Stabilizer

#1

Saw Blade Stabilizer

George@Colonel's Workshop-Havertown PA

>Good Morning Friends,

I had been using the thin kerf Forrest Woodworker II on my Jet contractor's saw w/o a stabilizer and had very good results. I sent the blade to Forrest to be resharpened and tested. When it was returned I had acquired a new Jet hybrid saw, and was then using a Leitz 40 tooth combination blade. When I swapped it out to install the Forrest I noticed a slight wobble in the Forrest which did not occur on the other saw. I can hear the wobble if I shut the saw down in mid cut. The wobble is also clearly visable as the saw spins down to a stop. There is no wobble with any other blades on the hybrid. I noticed the arbor washer is of a lesser diameter on the hybrid than it was on the old contractor saw, and theorize the larger washer on the old saw acted as an effective stabilizer. There does not appear to be any arbor shaft runout to speak of, as all my other Freud abnd Leitz blades run true. I think I better get a stabilizer for the Forrest WWII. Comments? Thanks.

George

Re: Saw Blade Stabilizer

#2

Re: Saw Blade Stabilizer

Dave Bair, Eaton Rapids, MI

>There is another explanation; the blade worked fine before you sent it to Forrest. And, if they "tested" it, why does it now wobble?

Re: Saw Blade Stabilizer

#3

Jesper, Denmark

Colonel, Sir.......

Jesper, Denmark

>Me thinks you better explain this to the sharpener - just like you did here. Something is wrong with this blade if all the others run true.

I am not sold on stabilizers. It is hard to put them on both sides of the blade, as all the saw settings have to be adjusted as the blade moves a stabilizer thicknes to the left or right, depending on your saw. using the one part of the stabilizer witht eh standard wask�her on the other side seems to me would just dish the blade for what purpose I do not know.

Re: Saw Blade Stabilizer

#4

Re: Saw Blade Stabilizer

Ken Garlock, Collin County Texas

>Good Afternoon, George.

When I sent my Forrest WWII in for sharpening, I asked them to check it for warp. A gent from Forrest called me and said yes it was slightly warped and that they could fix it. I cost me a couple bucks, but I must admit that I haven't had it on the saw yet. I have another WWII on now.

I think I would call the folks at Forrest and see what they say. I think they may owe you a warp fix. Or before contacting Forrest, I would seek out a fellow WW in the area, and check your blade on his saw.

Be careful not to exceed warp 8,

Ken

Re: Saw Blade Stabilizer

#5

Re: Colonel, Sir.......

Howard Acheson

>Jesper, the Forrest Stabilizer is as a single flat disk. It is perfectly flat and does not apply any pressure to the blade. The Freud stabilizer is a two component device I contains a raised ring around the outside perimeter on on face of each disk. This raised face grips the blade between the two disks Using just one disk would certainly cup the blade and should not be done.

Re: Saw Blade Stabilizer

#6

Re: Saw Blade Stabilizer

Scott Whiting - Glendale, AZ

>Whew! That's probably the only blade you own I haven't sharpened. :-)

To induce flutter or wobble in an existing blade take heat and/or pressure Forrest's equipment is even less likely than mine to add that during the sharpening process. In a heavy industrial setting the plate can actually fatigue and lose tension, I doubt you use it that hard. The least expensive way to test your theory about the larger saw flanges is to find somebody local with a contractors saw like your old one and give it a try.

In my experience the most likely scenario is the blade may have gotten pinched near when you took it out of service and just did not get noticed because you knew it was dull or maybe a shoulder got tweaked a bit as you removed the blade. If it is a shoulder it can be fixed by almost anybody (usually one left and an adjoining right tooth). If it is the plate it needs to be fixed by somebody like Forrest that has the ability to tension a plate. You can lay the blade on a known flat surface or use an indicator on the saw to check the shoulders.

What surprises me is if you paid Forrest to test the blade they did not find it. At this point if it were me I would call Forrest.

Scott

Re: Saw Blade Stabilizer

#7

Jesper, Denmark

Thanks ..................

Jesper, Denmark

>I go the two disks witht the raised flanges. I can see how they mi9ght help, but never liked the idea of moving everything 1/4" to the left.

I do not really understand how a flat disk on just one side would help, unless the blade was concave on that side??

I guess I do not need to either.

Re: Saw Blade Stabilizer

#8

Ken, I will act ON IMPULSE

George@Colonel's Workshop-Havertown PA

>

Re: Saw Blade Stabilizer

#9

Blade stablizer

Paul Waddle

>To wit,I offer another explanation: The blade was warpped slightly. Forest fixed it,but then it crawled back to its favorite conditon. Makes me mad enough to go to the DQ and forget about it. pw

Re: Saw Blade Stabilizer

#10

Re: Blade stablizer

Ralph Turney

>Man, I sure with I could, but the DQ next to my house closed...I'm still in mourning.

Re: Saw Blade Stabilizer

#11

How does it cut

Bill Tindall, E.TN

>Missing in this discussion is a report of how the blade performed. Many if not all my blades flutter momentary when coasting to a stop or accelerating but they cut fine when wound up to operating speed. Hence, I don't worry about it. I presumed it might be normal.

I suspect if a wobble big enough to see was present at operating speed the saw would vibrate severely.

Re: Saw Blade Stabilizer

#12

Re: How does it cut

George@Colonel's Workshop-Havertown PA

>Good Morning Bill, and Happy Sunday

The blade cuts well in the saw, but then it was sharpened only a few days ago. There is no vibration at speed which I can detect. But it does wobble when spinning down.

George

Re: Saw Blade Stabilizer

#13

Re: Thanks ..................

Howard Acheson

>>> I do not really understand how a flat disk on just one side would help, unless the blade was concave on that side??

Because it is machined flat, it does add some support, I guess. However, the primary purpose is to add spinning mass to the rotating blade. The more mass, the more likely it will reduce any vibration. At least that's the theory. Personally, I've never been convinced. Also, why do you suppose it's only one blade manufacturer who pushes a "dampener/stiffener"? And they are the ones that many think make the best blades. Good blades don't need dampener/stiffeners.