Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

finish for ash

Posts

finish for ash

#1

finish for ash

Bill Tindall, E.TN

>Ash is hard to finish. Many finishes yellow with age and yellowing on the whiteness of ash looks gross (IMO). I have been spraying a "water white" conversion varnish (Sherwin Williams) but even it yellows some.

What is available in the water based finishes that can be sprayed? I must admit that I tried a water based finish several years ago and was disgusted by the blue haze and the difficulty of spraying something with the viscous properties of water. Its only benefit was that it has not yellowed.

I can believe that things may have improved and I will try a recommendation if someone has a knowledgeable one. The finish must not yellow with age, it must be bright like a nitrocellulose lacquer and be practical to spray. Bottom line, can I get nonyellowing without giving up the desirable properties of solvent finsih?

Re: finish for ash

#2

Re: finish for ash

Lee Schierer - McKean, PA

>I've noticed that the water borne finishes tend to yellow considerably less than solvent based finishes. Deft Clear wood finish also yellows less than Polyurethane.

Lee

Re: finish for ash

#3

Ellis Walentine

Tried bleaching?

Ellis Walentine

>I built a dining room once where the designer specifically called for bleached ash. We used two-part bleach (sodium hydroxide/hydrogen peroxide) and topcoated with water-white solvent-based lacquer. It really came out nice and held its neutral lightness over time.

I have been using Velvit AquaShield water-borne polyurethane and like it very much. I would suggest trying it. You may decide you prefer it to NC lacquer.

Ellis

Re: finish for ash

#4

Target WB Finishes *LINK*

mdclor

>You might consider Target's 9000 SuperClear Polyurethane.


Oxford 9000

Re: finish for ash

#5

Re: finish for ash

Clint Searl, at the base of Haycock Mtn

>At the risk of beating a dead horse, unless there's an overiding reason not to use it, the most permanently water white finish I've found is solvent based acrylic or alkyd lacquer. IMO, the Sherwin williams formulations cannot be beat.

Clint

Re: finish for ash

#6

Where do you get it?

Lee Schierer - McKean, PA

>I looked up the Velvit AquaShield and it appears to have very limited distribution. Who carries it?

Lee

Re: finish for ash

#7

what is the product name

Bill Tindall, E.TN

>I have not seen anything in the local store that matches your description. They will order for me, or I can get stuff from a branch that more caters to furniture trade, but I need to be sure what to ask for.

Re: finish for ash

#8

Re: what is the product name

Clint Searl, at the base of Haycock Mtn

>DESCRIPTION

SHER-W00D� CAB-Acrylic Lacquer is formulated

to meet the water white and nonyellowing

demands of the furniture, kitchen

cabinet, and wood finishing markets. It is intended

as a clear topcoat over white, �pickled�

or light pastel stains where the best nonyellowing

properties are required. Cellulose

Acetate Butyrate (CAB)-Acrylic presents the

best chemistry of lacquers for resistance to

yellowing.

Advantages:

� Meets the federal HAPS rule for wood products

as packaged*

� Water-white color

� Excellent resistance to yellowing - superior

to all nitrocellulose compositions

� Meets KCMA specifications when applied

over Sher-Wood Vinyl Sealer T67F3, T67F5,

T67F6 or T67F7

� VOC under 5.6 lb/gal**

� Fast drying - similar to nitrocellulose lacquers

� May be used directly over solid color lacquers

as a �scuff coat�

� Excellent film clarity and color retention

� Application by conventional, airless or air

assisted airless spray equipment

� Excellent print resistance after overnight

dry

� May be used as a shading lacquer or toner

by adding small quantities of Chroma Chem

844 colorants

� Free of lead hazards as packaged in compliance

with Consumer Product Safety

Commission's (CPSC) 16 CFR Chapter II:

Subchapter B, part 1303.

CHARACTERISTICS

Gloss(measured on black glass):

Gloss 85+ units

BRE 55-59 units

MRE 30-34 units

DRE 17-21 units

Volume Solids: 19.2 � 1%

Viscosity:

26-32 seconds#2 Zahn Cup

23-26 seconds#4 Ford Cup

Recommended film thickness:

Mils Wet 4.5 - 6.0

Mils Dry 0.7 - 1.0

Spreading Rate (no application loss)

310-443 sq. ft./gal. @ 0.7-1.0 mil dft

Drying (77�F, 50% RH):

To Touch: 10 minutes

To Handle: 15-20 minutes

To Sand: 30-60 minutes

To Recoat: 30-60 minutes

Force Dry: 10-20 minutes at

110-140�F

Flash Point: 37�F Pensky-Martens

Closed Cup

Package Life: 18 months, unopened

Air Quality Data:

Non-photochemically reactive

Volatile Organic Compounds (VOC)

as packaged, maximum

5.60 lb/gal, 672 g/L

3.20 lbs VOC/lb solids

Hazardous Air Pollutants (HAPS)

as packaged,

less than 0.8 lbs per pound of solids

An Environmental Data Sheet is available

from your local Sherwin-Williams facility.

CC-F23 10/07 continued on back

SPECIFICATIONS

Wood (interior only): Must be clean, dry,

and finish sanded. Substrate should be

free of grease, oil, dirt, fingerprints, and

any contamination to ensure optimum

adhesion and coating performance properties.

Moisture content of wood should be 6 to

8%.

Testing: Due to the wide variety of substrates,

surface preparation methods,

application methods, and environments,

the customer should test the complete

system for adhesion and compatibility

prior to full scale application.

Wood Finishing System:

1. Apply full wet coat of Sher-Wood Vinyl

Sanding Sealer, T67F3 or T67F6

2. Air dry 30 minutes, sand, remove all

sanding dust.

3. Apply full wet coat of Sher-Wood CABAcrylic

Lacquer and allow 30-60 minutes

drying.

4. For more depth and better appearance,

apply a second coat.

SHER-WOOD� CAB-Acrylic Lacquer

Gloss ................................... T75C15

Bright Rubbed Effect ............ T75F16

Medium Rubbed Effect ......... T75F17

Dull Rubbed Effect ............... T75F18

*National Standards for Hazardous Air Pollutants

(HAPS) Emissions for Wood Furniture

Manufacturing Operations CFR40, Part 63,

Subpart JJ

CC-F23

Chemical Coatings

**VOC compliance limits vary from state to

state; please consult local Air Quality rules

and regulations.

APPLICATION

Reduction

In high humidity conditions or where

blushing is evident, add 1-2% Butyl

Cellosolve, R6K25, or MAK, R6K30, as

a HAPS compliant alternative.

Typical Setups

Conventional Spray:

Air Pressure ..........................45-65 psi

Fluid Pressure .......................... 6-8 psi

Reducer ....................................... none

Airless Spray:

Pressure ...................... 1200-1800 psi

Tip ........................................ .011-.015"

Reducer...................... . HAPS compliant

lacquer thinner, R7K320 as needed up to

10%. Lacquer thinner, R7K120 may also

be used, but is not HAPS compliant.

Air Assisted Airless:

Air Assist ...............................10-15 psi

Fluid Pressure ................. 400-600 psi

Cap/Tip ................................ .011-.015"

Reducer ..........................HAPS compliant

lacquer thinner, R7K320 as needed up to

10%. Lacquer thinner, K120 may also be

used, but is not HAPS compliant.

Cleanup:

Clean tools/equipment immediately after

use with HAPS complying lacquer

thinner, R7K320 or R7K322. Lacquer

thinner K120 or K22 may also be used,

but are not HAPS compliant.

Follow manufacturer's safety recommendations

when using any solvent.

SPECIFICATIONS

Product Limitations:

� Surface to be finished must be free of

grease, dirt, and other foreign matter.

� Sher-Wood Vinyl Sealer, T67F3,

T67F5, T67F6 or T67F7, must be used

as a sealer to meet the KCMA specification.

Do not use any other lacquer

or vinyl sealers under CAB-Acrylic Lacquer.

� Self-sealing systems are not recommended.

� Maximum cure and resistance properties

are not obtained for at least 14

days air drying.

� Yellowing over white and pastel colors

may occur due to the yellowing tendency

of the color system (stain,

basecoat, etc.), and not to the clear

CAB-Acrylic topcoat.

� For interior use only.

� Agitate thoroughly before use.

� To maintain HAPS compliance only

reduce with HAPS compliant reducers.

CAUTIONS

Thoroughly review product label for

safety and cautions prior to using this

product.

A Material Safety Data Sheet is available

from your local Sherwin-Williams facility.

Please direct any questions or comments

to your local Sherwin-Williams facility.

LABEL CAUTIONS

CC-F23 SHER-WOOD� CAB-Acrylic Lacquer

Performance Tests:

Wood test panels prepared with one coat Sher-

Wood Vinyl Sealer, T67F3 and two coats Sher-

Wood CAB-Acrylic Lacquer, T75F17 (MRE).

Allowed to ambient age 30 days

Panels tested per KCMA Chemical Resistance

methods.

Household Chemicals Test

Vinegar ............................................ no effect

Lemon Juice ................................... no effect

Orange Juice .................................. no effect

Grape Juice .................................... no effect

Tomato Catsup ............................... no effect

Coffee ............................................. no effect

Olive Oil .......................................... no effect

100 Proof Alcohol ........................... no effect

Water and Detergent, 1% ............... no effect

Mustard (1 hour) ........ very slight discoloring

Cold Check Resistance ................ 20 cycles

Resistance to Discoloration�films cast on

white porcelain and exposed to 200 hours

Mercury vapor sunlamp showed virtually no

yellowing while conventional nitrocellulose lacquer

exhibited substantial yellowing

Note: Product Data Sheets are periodically

updated to reflect new information

relating to the product. It is important that

the customer obtain the most recent

Product Data Sheet for the product being

used. The information, rating, and

opinions stated here pertain to the material

currently offered and represent the results

of tests believed to be reliable. However,

due to variations in customer handling

and methods of application which

are not known or under our control, The

Sherwin-Williams Company cannot make

any warranties as to the end result.

SEE CONTENTS STATEMENT ON LABEL.

Contents are FLAMMABLE. Vapors may cause flash

fires. Keep away from heat, sparks, and open flame.

During use and until all vapors are gone: Keep area

ventilated - Do not smoke - Extinguish all flames,

pilot lights, and heaters - Turn off stoves, electric

tools and appliances, and any other sources of ignition.

VAPOR HARMFUL. Use only with adequate ventilation.

Wear an appropriate properly fitted vapor/particulate

respirator (NIOSH approved) during and after

application, unless air monitoring demonstrates

vapor/mist levels are below applicable limits. Follow

respirator manufacturer�s directions for respirator use.

Avoid contact with eyes and skin. Wash hands after

using. Keep container closed when not in use. Do not

transfer contents to other containers for storage.

FIRST AID: If INHALED: If affected, remove from

exposure. Restore breathing, Keep warm and quiet.

If on SKIN: Wash affected area thoroughly with

soap and water. Remove contaminated clothing.

Launder before re-use. If in EYES: Flush eyes with

large amounts of water for 15 minutes. Get medical

attention. If SWALLOWED: Call Poison Control Center,

hospital emergency room, or physician immediately.

SPILL AND WASTE: Remove all sources of ignition.

Ventilate and remove with inert absorbent. Incinerate

in approved facility. Do not incinerate closed

container. Dispose of in accordance with Federal,

State, and Local regulation regarding pollution.

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE.

Contains solvents which can cause permanent brain

and nervous system damage. Intentional misuse by

deliberately concentrating and inhaling the contents

can be harmful or fatal.

WARNING: This product contains chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE

REACH OF CHILDREN.

FOR INDUSTRIAL USE ONLY.

SEE MATERIAL SAFETY DATA SHEET.21363-

051905.SHER-WOOD� CAB-Acrylic Lacquer

DESCRIPTION

SHER-WOOD� Moisture Resistant

Lacquers are self sealing general purpose

topcoats specially designed for resistance

to moisture and household

chemicals.

Advantages:

� Meets the Federal HAPS rule for wood

finishes as packaged*

� Excellent moisture resistance

� Excellent resistance to household

chemicals

� Self sealing

� Non-photochemically reactive

� Excellent adhesion

� Excellent cold check resistance

� Excellent print resistance

� Meets the test requirements of KCMA

specifications (See Specifications section)

CHARACTERISTICS

Gloss: Gloss Full

MRE 30-34 units

DRE 17-21 units

Weight Solids: 24 � 1%

Volume Solids: 16 � 2%

Viscosity:

28-33 seconds #2 Zahn Cup

Recommended film thickness:

Mils Wet 5.0 - 6.0

Mils Dry 0.8 - 1.0

Spreading Rate (no application loss)

@ 0.8-1.0 mil dft: 265-331 sq ft/gal

Drying (77�F, 50% RH):

To Touch: 10-15 minutes

To Handle: 30-45 minutes

To Recoat: 60 minutes, do not

exceed 12 hours

Force Dry:

To Sand 10 minutes at 140�F

To Recoat: 15 minutes at 140�F

To Pack: 60 minutes at 140�F

Flash Point: 22�F Pensky-Martens

Closed Cup

Package Life: 3 years, unopened

Air Quality Data:

Non-photochemically reactive

Volatile Organic Compounds (VOC)

as packaged, maximum

5.63 lb/gal, 673 g/L

3.17 lbs VOC/lb solids

Hazardous Air Pollutants (HAPS)

as packaged, maximum

less than 0.8 lbs per pound of solids

An Environmental Data Sheet is available

from your local Sherwin-Williams facility.

CC-F7 04/05 continued on back

SPECIFICATIONS

Wood (interior only): Must be clean, dry,

and finish sanded. Substrate should be

free of grease, oil, dirt, fingerprints, and

any contamination to ensure optimum

adhesion and coating performance properties.

Moisture content of wood should be 6 to

8%.

Testing: Due to the wide variety of substrates,

surface preparation methods,

application methods, and environments,

the customer should test the complete

system for adhesion and compatibility

prior to full scale application.

Wood Finishing System:

Three Coat System

1. Moisture Resistant Lacquer, dry one

hour

2. Moisture Resistant Lacquer, dry one

hour, sand with stearated paper

3. Moisture Resistant Lacquer

Sanding Sealer System

1. Vinyl Sanding Sealer, T67F3, T67F5,

T67F6 or T67F7, dry 30 minutes and

sand

2. Moisture Resistant Lacquer, dry one

hour

3. Moisture Resistant Lacquer

The 3 coat system is ideal for customers

who like to limit the number of finishing

materials they must have on hand to one

product.

SHER-WOOD�

Moisture Resistant Lacquer

Gloss ................................... T70C20

Medium Rubbed Effect ......... T70F22

Dull Rubbed Effect ............... T70F23

*National Standards for Hazardous Air

Pollutants (HAPS) Emissions for Wood

Furniture Manufacturing Operations

CFR40, Part 63, Subpart JJ

CC-F7

Chemical Coatings

APPLICATION

Typical Setups

Reduction: Normally not required. If reduction

is needed use HAPS Compliant

Lacquer Thinner, R7K320 or R7K322.

Lacquer thinner K22 or K120 may also

be used, but are not HAPS compliant.

May be applied by:

Conventional

Airless Spray

Warm Spray

Curtain Coating

Consult your Sherwin-Williams Representative

for details.

Conventional Spray:

Air Pressure .......................... 50-65 psi

Fluid Pressure ....................... 12-15 psi

Cleanup:

Clean tools/equipment immediately after

use with HAPS complying lacquer

thinner, R7K 320 or R7K322. Lacquer

thinner, K120 or K22, may also be used,

but are not HAPS compliant.

Follow manufacturer's safety recommendations

when using any solvent.

Moisture Resistance Test:

Birch panels were finished with 3 coats of Gloss

Moisture Resistant Lacquer, with 1 hour drying

between coats. The front, back and all sides were

finished.

1. An "X" cut was made through the finish to the

wood. This was covered with a wet synthetic

sponge for 16 hours. After sponge removal, a

whitening appeared, on the cut, which disappeared

after 2 hours.

2. KCMA Finish Test, F-4, Detergent and Water

Test�no effect.

Performance Tests:

Cold Check Resistance .................. 20 cycles

Print Resistance ................................. No print

3.0 mils dft, 18 hours air dry, at 1 psi at 77�F in

direct contact with 8 oz. duck cloth.

Household Chemicals Test

Maple panels were finished with 3 coats of Gloss

Moisture Resistant Lacquer, with 1 hour drying

between coats. After film was aged 30 days at

77�F, 5 drops of each item were placed under a

watch glass for one hour. The film was rinsed

with water, washed with soap and water, dried

and wiped with VM&P Naphtha to remove items

not removed with water. After removal, the finish

was examined and the following results noted:

Household Ammonia .......... slight haze/dulling

Vinegar ................................... no visual effect

Lipstick ................................... no visual effect

Lemon Juice ........................... no visual effect

50% Ethyl Alcohol .................. no visual effect

Mercurochrome 2% ................ no visual effect

Washable Blue Ink ................. no visual effect

Mustard .................................. no visual effect

Oil Base Paint ........................ no visual effect

Latex Emulsion Paint ............. no visual effect

VM&P Naphtha ...................... no visual effect

Turpentine .............................. no visual effect

Orange Crayon ....................... no visual effect

Carbon Tetrachloride .............. no visual effect

Mayonnaise ............................ no visual effect

10% Sodium Carbonate ......... no visual effect

Sour Milk ................................ no visual effect

Margarine ............................... no visual effect

Butter ..................................... no visual effect

Water ..................................... no visual effect

Grease (Cooking fat) .............. no visual effect

CC-F7 SHER-WOOD� Moisture Resistant Lacquer

CAUTIONS

Thoroughly review product label for

safety and cautions prior to using this

product.

A Material Safety Data Sheet is available

from your local Sherwin-Williams facility.

Please direct any questions or comments

to your local Sherwin-Williams facility.

LABELS CAUTIONS

SEE CONTENTS STATEMENT ON LABEL.

Contents are FLAMMABLE. Vapors may cause flash

fires. Keep away from heat, sparks, and open flame.

During use and until all vapors are gone: Keep area

ventilated - Do not smoke - Extinguish all flames,

pilot lights, and heaters - Turn off stoves, electric

tools and appliances, and any other sources of ignition.

VAPOR HARMFUL. Use only with adequate ventilation.

Wear an appropriate properly fitted vapor/particulate

respirator (NIOSH approved) during and after

application, unless air monitoring demonstrates

vapor/mist levels are below applicable limits. Follow

respirator manufacturer�s directions for respirator use.

Avoid contact with eyes and skin. Wash hands after

using. Keep container closed when not in use. Do not

transfer contents to other containers for storage.

FIRST AID: If INHALED: If affected, remove from

exposure. Restore breathing. Keep warm and quiet.

If on SKIN: Wash affected area thoroughly with

soap and water. Remove contaminated clothing.

Launder before re-use. If in EYES: Flush eyes with

large amounts of water for 15 minutes. Get medical

attention. If SWALLOWED: Do not induce vomiting.

Call Poison Control Center, hospital emergency room,

or physician immediately.

SPILL AND WASTE: Remove all sources of ignition.

Ventilate and remove with inert absorbent. Incinerate

in approved facility. Do not incinerate closed

container. Dispose of in accordance with Federal,

State, and Local regulation regarding pollution.

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE.

Contains solvents which can cause permanent brain

and nervous system damage. Intentional misuse by

deliberately concentrating and inhaling the contents

can be harmful or fatal.

WARNING: This product contains chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE

REACH OF CHILDREN.

FOR INDUSTRIAL USE ONLY.

SEE MATERIAL SAFETY DATA SHEET. 21513-

100402.

SPECIFICATIONS

Product Limitations:

� Surface to be finished must be free from

grease and other foreign matter.

� Apply all coats within a 12 hour period or

lifting may occur.

� Apply directly to bare or stained wood for

best adhesion and moisture results. Adhesion

may be impaired and resistance to

moisture lowered if used over lacquer

sealer. If a sealer is desired use Sher-

Wood Vinyl Sealer, T67F3, T67F5, T67F6

or T67F7.

� If spraying conditions are above 50% RH,

use MAK, R6K30, to prevent wet film blushing.

Such drying conditions will lengthen

time to harden the film.

� Customer urged to pretest system under

shop conditions.

� Sand and remove sanding dust between

each coat.

� Not recommended for exterior use.

� To maintain HAPS compliance only reduce

with HAPS compliant reducers.

Note: Product Data Sheets are periodically

updated to reflect new information

relating to the product. It is important that

the customer obtain the most recent

Product Data Sheet for the product being

used. The information, rating, and

opinions stated here pertain to the material

currently offered and represent the results

of tests believed to be reliable. However,

due to variations in customer handling

and methods of application which

are not known or under our control, The

Sherwin-Williams Company cannot make

any warranties as to the end result.

Re: finish for ash

#9

Oh, CAB lacquer

Bill Tindall, E.TN

>I am familiar with this material. The CAB part is made just down the road from where I live and it is stocked by the local store.