Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Help with warped panel

Posts

Help with warped panel

#1

Help with warped panel

JohninRI

>Good Morning,

I need your help with some warped panels. I am an amatuer woodworker and I have spent the last two weeks milling some cherry into panels and found them warped yesterday. Here is the information that I can offer:

The cherry was rough sawn on a bandsaw mill over 10 years ago and has been in my unheated shop for over 7 years. I joined and planed it two weeks ago and it is now 3/4 in thick. I glued up the panels last week to a width of 19 inches and a length of 48 inches. I did not concern myself as much with the rings as I did wih the grain matching. I then sanded one side to 220 grit. Once completed, I stood them on end on my concrete floor and leaned them against my wall.

So that's where I stand. I am sure that I can rip them and reglue them, but I have heard that I could wet one side and bring them back.

I plan on using the panels for a chest of drawers that I will through dovetail toether. Any thoughts or ideas would be greatly appreciated.

Thanks,

John in RI

Re: Help with warped panel

#2

hard to keep a good panel flat

Bill Tindall, E.TN

>You have encountered a common problem. Searching WC archives will uncover numerous discussions that began with a question just like yours. Fortunately dealing with it is less onerous that cutting all the dovetails and getting the box glued successfully. If you are indeed inexperienced, do not underestimate the challenge of gluing up a dovetailed box. Seek experienced help if you have some available. Use a very slow setting glue such as liquid hide and have oodles of clamps on hand. I would have suggested making a box from poplar for practice. If the practice piece turns out ok it will be useful for something. I have lots of poplar practice pieces around, including a trunk.

But, back to the question....

You need to have the panel dead flat to make the transfer marks if you are cutting by hand, or the jig needs to mash the panel flat if cutting by machine. There are two approaches that I have used.

Tedious approach: The concave side is dryer than the convex side. Put down a piece of news paper. Spritz it with water-damp not soaked. Add a second sheet and lay the panel on it, concave side down. Before your eyes it will bow the other way. Remove when its right and do dovetails quickly while it is in this fleeting state of flatness. Alternatively, expose the convex side to drier conditions than concave side- sun, lay on floor in heated room, etc, use your imagination.

Get on with it approach: Mash it flat while cutting the dovetails. I clamp a 2 x 2 across the width while hand cutting. My jig mashes it flat while machine cutting. In any case it needs to be dead flat during cutting by hand or machine.

If the dovetails are cut with the panel mashed flat the panel will flatten when the box is assembled.

If this was a top it would mash flat when fastened to case or frame.

Re: Help with warped panel

#3

Re: Help with warped panel

Lee Schierer - McKean, PA

>Your mistake may have been to set the panel on the concrete floor leaning against the wall. The moisture from the concrete floor and from the wall probably changed the MC of the wood only on one side. Try standing the panels in the same location with the other side toward the wall for a couple of days.

Or dampen the concave side and place the panels on a flat surface with stickers below them and between them. Weight the panel down with planty of weight set on stickers.

When ever you plane material make sure you remove equal amounts of wood from each side of the board whenever possible. This practice will help keep the moisture content constant on both sides. It is also a good idea to remove only small amounts and let the boards acclimate before removing additional material. Boards should be stacked, stickered and weighted during the acclimation process.

Finally make sure the boards making up a panel are clamped up so the clamp up is flat. If the jointed edges are not perfectly square to the face the glue up will have the appearance of the panel cupping. It only takes a 1 degree error to produce a noticeable cup in a panel.

If the panels don't flatten with the two suggestions above, If you have the wood to spare, Rip the panels along the glue lines, re-joint the edges and re-glue them. Alternating the grain may help if the indiviudal boards are actually cupped.

Lee

Re: Help with warped panel

#4

Re: Help with warped panel

John Ross

>Thank You Guys,

I have removed the panels from the floor and plan on giving the flattening process a try. I had planned on hand-cutting the joints, but I think the jig will come into play now. You have saved me some hair, I am sure.

Thank You again,

John in RI