Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Hide Glue Part II-hammer veneering in dry climates

Posts

Hide Glue Part II-hammer veneering in dry climates

#1

Hide Glue Part II-hammer veneering in dry climates

GolfSteve in Calgary

>Part II - hammer veneering in dry climates

For a while now I've been hammer veneering with hot hide glue. This, in my opinion, is where hot hide glue really shines. For small to medium sided panels I find hammer veneering is much easier than fighting with PVA glue, curling veneer, cauls, battens, squeeze out or bleed-through interfering with your finish, etc�..

However, last night I spoke briefly with one of our local recognized "experts" in the field. He is English trained and emigrated to Canada many moons ago. He gave a presentation on veneering to our club last night, but he noticeably left out any discussion of hammer veneering. I asked him about this after the meeting and said that in our very dry Calgary climate hammer veneering was problematic due to cracks appearing in the veneer. The problem is the large amount of moisture that enters the veneer from the hide glue. The subsequent drying causing cracking of the veneer. He does not recommend hammer veneering for that reason. We did not have time to chat, so I was not able to ask more questions about why the moisture in PVA doesn't cause similar problems.

This might be the cause of some cracking that I experienced last year�.I had put it down to the use of crotch veneer, but perhaps it was caused by the hot hide glue in a dry climate? The cracks appeared about a month after the piece was veneered. This has happened to me twice, but both times it was with the crotch veneer. I've hammer veneered straight grained cherry several times with no problems. I've also hammer veneered figured sawn veeneer (1/8" thick) with no problems yet but it was only veneered a week ago.

Here's a picture of the cracked crotch veneer and a piece of the piece:



I really hope that I can continue hammer veneering, but if it is a problem in dry climates I might have to switch to a different method. Has anyone else heard of or experienced this problem with hammer veneering in dry climates?

Thanks in advance,

Steven

Re: Hide Glue Part II-hammer veneering in dry climates

#2

Re: Hide Glue Part II-hammer veneering in dry clim

Wayne Carson "TX"

>I live in West Texas Lubbock and I veneered 8 panels ov 1/4" MDF with white oak last year and haven't had any cracking with the hide glue and yesterday the RH was 8%. I will wait until next year and see if there is any cracking. Did you wet the veneer prior to gluing it down? I sprayed mine with RO water before I hammered it.

Re: Hide Glue Part II-hammer veneering in dry climates

#3

Re: Hide Glue Part II-hammer veneering in dry clim

GolfSteve in Calgary

>I had softened the veneer with a commercial softerner, the dried the veneer between weighted plattens and sheets of paper tower. So the veneer should have been pretty dry when I started veneering.

Re: Hide Glue Part II-hammer veneering in dry climates

#4

Well Part II

Stephen Shepherd in the State of Deseret

>Steve,

I have seen and experienced the same thing with crotch mahogany and I think the problem is the veneer rather than the glue.

If you have had success with cherry it was because it didn't have the tension within a crotch. Some old examples have the same cracks that were just filled in the finishing process.

I would imagine you would have the same problem using any glue, it is the crotch mahogany veneer that is the problem. This doesn't happen to all crotches and can vary from tree to tree and different species as well. African mahogany is more difficult to work with, tough on tools and difficult to glue.

Don't give up on hide glue for this reason (or any reason), it is still the best glue in the world (did I say that?).

Stephen