Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

recent work

Posts

recent work

#1

recent work

Robin Corell in Atascadero, CA

>I recently compleated this silver chest and finaly got around to taking some pics. this was commisioned by a client to house a coin colection. The overall height is 66" and the cabinet part is 14" at its widest and 12" deep. It is all solid wood with claro walnut being the primary and port orford cedar and monterey cypress being used for the drawer sides and some other interior parts. The pulls are turned out of some curly olive. I had originaly intended to make the pulls out of hammered silver but between the rising cost of silver and the time to make them I couldn't fit it into the budget. As with many of my commisions I made two of these, one for the client and one to take to shows and sell. the one on spec will have carved monterey cypress panels. It may surprise many but the most dificult part was the lower streatchers.

Robin


img

Re: recent work

#2

Re: recent work

Robin Corell in Atascadero, CA

>I resawed some narrow boards and arranged them to make it look as if all the drawer fronts were cut from a single wide board. This required me to scrap a little more wood than what was actualy used in the drawer fronts. it is not really very visable but you can see from the shape of the stiles and rails that the railes on the side while straight are curved in profile to match the curves of the front of the cabinet.

This paragraph is a special note for Dominic. The 5/8"x3/8" champher around the drawers was not originaly part of the design. while moving the carcas around I inadvertently gouged the inside edge of the opening. adding the champher was actualy a solutuion to fixing a mistake. We all make mistakes the key to becomeing a good woodworker is in getting good at fixing them.

Robin


img

Re: recent work

#3

Re: recent work

Barry Irby

>Robin, This is truly outstanding. Wonderful work.

May I ask a couple of questions? How tall are you? And What kind of car do you drive? No! Wait, those were not the questions. Would you explain what made the lower stretchers so difficult? And what do your clients think of you making and selling a duplicate? Do they suggest the design or is it yours? Seems to me your clients would want an original and a once off piece.

And, I'm not him, but really nice save on that gouge.

Re: recent work

#4

JL

Re: Nice - can you show stretcher detail?...

JL

>I really like the "lifted" effect that you got.

Re: recent work

#6

Re: recent work

charlie belden

>I think the Design Gods were telling you something when you dinged that edge. The chamfer a) adds shadow lines to the front and b) eliminated a sharp edge that might have contacted skin - and dinged IT or even cut it. Sharp edges can do that, be they on a cutting tool - or wood.

Getting the drawers to fit "just so" must've been a lot of fun.

More about the stretchers and joinery please.

charlie belden

Re: recent work

#7

Ellis Walentine

Nice design, Robin

Ellis Walentine

>I think you have done a great job with this design. The legs look very solidly grounded, their upward motion is graceful (and nicely complemented by those difficult stretchers), and the cabinet plays well off the shape and direction of the legs.

I am curious about a few things: What was difficult about the stretchers? How did you make the side panels? How did you work those drawer fronts to produce the rustic look? Got any detail shots of a couple drawers pulled partway out? What do the drawer interiors look like? (Any specialty coin collection layouts?)

I'm going to try to keep my wife from seeing this. She's been waiting half a lifetime for a jewelry chest. :-)

Ellis

Re: recent work

#8

Re: recent work

Robin Corell in Atascadero, CA

>As wood workers we are ale pretty comfortable working with 90*,45* angles and to some extent 22.5,30, and 60* as well as they are all common detents on out tools. On a piece of furniture that is rectangular the diagonals meet at some less common angle. This in itself is not overly difficult. In my silver chest the legs are also at a 5* angle and they are also tapered on the front, back, and outside (viewing the cabinet from the front) this adds a bit more complication. Throw in the curve of the stretchers and I would have been hard pressed to make it any more difficult if I tried. In the pic you can see my Rube Goldberg set up for making the lay out for the joint detail on the center of the stretcher. I needed to place the stretcher in place and draw the diagonals and then using a square with an extra blade held in place with a rule clamp I was able to plumb down from the lines I drew on the top. This let me connect the lines on the bottom side. Near the edges of the pic you can see a rule clamped across the legs. The rule is parallel to the floor and as you can see the aris on the bottom of the joint is an angle rather than parallel to the ground. This is due to the angle and taper of the legs and it made the end cross section of each stretcher trapezoidal in shape and was some weird compound angle.

When I make two of a single commission I usually don't make them exactly the same. On the last pair of jewelry chests I gave the client who commissioned it her choice of the two finished chests and then I made some tall legs for the spec chest as hers was made to sit on top of a dresser. For this chest the spec piece will have light colored panels with a carved pattern on them and will likely change the drawer pull detail. So in essence each chest has its unique identity.

The client who commissioned this chest is about 6' tall but I did mention that I thought the top drawer would be unusable and the next two drawers would be of limited use. I was assured that they would all be used and not to worry about it as he liked the design and I should make it how I wanted to.

Robin


img

Re: recent work

#9

Re: Nice - can you show stretcher detail?...

Robin Corell in Atascadero, CA

>Here is a shot that shows the how the center joint was made. Cutting the joint was not particularly difficult or time intensive it was the layout that made things difficult.

Robin


img

Re: recent work

#10

JL

Re: Thanks

JL

>

Re: recent work

#11

Re: Nice design, Robin

Robin Corell in Atascadero, CA

>Thanks for the kind words. I have posted a couple of pics of making the stretches up above. I think what made them difficult was two things. First is that with my background as patternmaker I use a few different techniques than most furniture makers and for me curves are not particularly hoard or time consuming. So the rest of the cabinet, while some parts were time intensive none of it was particularly difficult. The second thing that made the stretches difficult was that they caught me by surprise. I don't work from drawings and in this case I am not sure if the complexity of the joint would have shown up. By the time I got to the stretches the rest of the cabinet and all the drawers were done and I thought I would knock out the stretchers in a few hours.OOPS, miss calculation on that. The funny part is I had complete autonomous creative control and could have changed the design at the last minute without client approval but this is how I thought it needed to be. I guess that is why the client gave me that creative freedom.

I attached a pic of shaping the pieces for the side panels. In the pic I am making the parts for the panels that will be carved and for those I used a piece of quarter sawn wood which gave me some plane sawn panels with a fair bit of wild grain. This will compliment the carved pattern. On the commissioned chest I used a piece of plain sawn wood to cut the parts out of which gave me a quarter sawn panel. This was important to the design as I did not want any wild grain run out to show in the panels. I then made several fences for my router table to cut the rabbits on the edges. I needed a total of nine fences for my router table but again curves are pretty easy for me and I was able to make all the fences and cut the rabbits in under a day.

If it isn't clear from the pic I made a template to trace the part on the board and then cut close to the line and finished shaping on my spindle sander. By not cutting the entire part out I have more control while shaping on the spindle sander. I then finished cutting it out and shaped the outside of the curve on my disc sander. A total of six pieces were needed for each panel. The glue up was actually very simple. I just did a basic rub joint with hide glue and came back the next day to tight joints.

I think the rustic look you are seeing may be a moir� pattern in the digital pic. the drawer fronts have a 1/16 gap between each other as well as on the edges and I think this is distorted in the digitalization of the pic to make it look like they are tilted in or out. I went to great pains to get them all even and flush and am re thinking that clean contemporary look vs. cock beading.

The drawers are constructed with a sliding dovetail on the fronts and a rabbit and dado on the rear. Because of the curved sides I needed to attach a strip of wood to transition from the curve to the straight drawer sides. These blocks also house the strips of wood used for the drawer guides. I have sent pieces of paper to the client so he can layout his coins and once I get tem back I will make the interior deciders. They will be basic egg crate construction half the depth of the drawer. I line the drawer bottom and sides with PSA felt but not the dividers.

Robin


img

Re: recent work

#12

Bravo!

Bill Tindall, E.TN

>I enjoyed seeing the pictures of this piece and the in depth discussion on its construction.

Pieces like this are inspirational. I often dismiss the possibility of making something, for example a piece with curves, until I see that someone else has done it. Not that I will ever approach this work, but I might now try something with a curve or a artful stretcher.

Re: recent work

#13

Re: recent work

HC Sakman

>Hi Robin,

I think the piece is unique and attractive, thanks to your mistake which forced you to put chamfer around the drawers! I think it adds so much depth to the piece, That's what I call "A Happy Accident"! ;-)

I think it turned out great. I also like the handles.

Be proud.

Chico...

Re: recent work

#14

Re: Bravo!

Robin Corell in Atascadero, CA

>Thanks for the comments. I can't compete on price with the big factories or off shore so I have to compete by my designs being unique. From the very beginning a couple of ways I have done this are by incorporating curves and I also usually add a bit of hand carving in the form of a textural pattern.

The other way I try to keep my work unique is by using different profiles. All woodworkers have access to the same router and shaper profiles. What I do is draw the profile that suits my needs and then come up with a way to make it. It is not as difficult as it sounds and can often be done making several passes with different bits and blending a line or two with a scraper or a bit of sandpaper. Often my profiles are large radii cut with a spokeshave or in the case of this cabinet it was a large chamfer that was at an angle other than 45*. These subtle differences often don't stand out as glaringly unique, but they do contribute to an overall design that is.

Robin