Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Table top attachment questions of ye:

Posts

Table top attachment questions of ye:

#1

Table top attachment questions of ye:

Pete in Holland, MI

>Guys -

Building some Mission-style coffee/end tables with a glued-up top. Want to attach the tops to the leg frame work with some little wood blocks inserted to grooves machined into the leg skirts, kinda like I've seen Norm do on occasion. Couple questions though:

1) In relation to the finished table, should the grain in these cleats run vertically or horizontally (end grain faces the skirt groove)?

2) How thick of "toe" should I use to insert into the mating groove, which will be sized appropriately?

3) In order for the top to float thru the seasons, I know it can't be glued to the table skirt. Does the varnish pose a threat to this floating, or are there tricks out there to prevent the varnish from weeping between the top and skirt, adhereing the two pieces together?

Thanx !

Re: Table top attachment questions of ye:

#2

Re: Table top attachment questions of ye:

Lee Schierer - McKean, PA

>The grain should run the length of the blocks.

The tab should be about 1/4" thick and about the same depth into the side skirts.

Since your top is floating, finish the legs and skirt separately from the top. Do a dry assembly first to make sure it all fits. Then finish both sides of the top and do the final assembly once the finish is completely cured.

lee

Re: Table top attachment questions of ye:

#3

Re: Table top attachment questions of ye:

Pete in Holland, MI

>Lee -

I know the grain should run the length of the block, but should it run vertically (like the axis of the screw hole), or horizontally, crossing the screw hole, or does it really make a difference ?

Re: Table top attachment questions of ye:

#4

Re: Table top attachment questions of ye:

Lee Schierer - McKean, PA

>The grain should run perpendicular to the screw hole. If it is parallel to the screw hole it will probably crack when teh screw is tightend or after a while when the stresses work on it a for a bit.

lee

Re: Table top attachment questions of ye:

#5

Re: Table top attachment questions of ye:

Robin Corell in Atascadero, CA

>I use my biscut joinner to cut the slots and have never had a problem with the tabs being 1/8" thick. Walnut workes well for the blocks because it is strong and not prone to spliting. The whole purpose of the blocks is to allow free movement, I have always attached the top after finishing.

Robin

Re: Table top attachment questions of ye:

#6

Re: Table top attachment questions of ye:

Pete in Holland, MI

>Thanks guys -

Kinda what I was thinking, but wanted to confirm it.

Pete

Re: Table top attachment questions of ye:

#7

Funny you should ask...

Tony - Memphis

>I am to that stage in my current project. I was looking for some historically correct methods, but none that I found pleased me. I have built a few tables and used buttons with great success. I just made mine by rabbeting a long piece of wood, drilling the holes, then cutting off the buttons. I usually make the groove for the button before construction, but I failed to do that this time. I have heard about using the biscuit jointer for making the grooves. Also thought about a router with a three wing cutter. Garrett Hack did an article in FWW (I think) about this subject. I usually wax the groove and the button to allow things to move easily. My button height is a wee bit smaller than the groove bottom edge so that I know it will pull the top a little when I tighten it (not too tight!). I've seen some metal pieces (or buttons as I am calling them) in some of the catalogs that would probably work well too. I just use the wood since I usually have the perfect size board laying around. I usually make a bunch at a time too. Anyway, good luck with your project. And I too finish the top before assembly.

Tony

Re: Table top attachment questions of ye:

#8

Re: Funny you should ask...

John in Kerrville

>You could always use Festool's new Domino for cutting the grooves (ducking and running).

Re: Table top attachment questions of ye:

#9

Re: Funny you should ask...

Tony - Memphis

>Lemme run that by the wife! Actually, this particular table must be as good as a fancy antique as we have the same amount of money invested! This table was the subject of a 2 week class at Phil Lowe's Furniture Institute of MA summer before last (has it really been that long?). The class was my 40th birthday present. It was a great time and I really enjoyed it. We didn't finsh the table and I shipped back a couple of boxes of parts. I was in the middle of a couple of other projects, so I assembled what was done in the dining room and it sat there in the rough for a long time. I finally got it out in the shop and am almost finished. I routed the thumbnail edge on the top last night and I need to make the drawer bottoms. This pic is old, but shows what it sort of looks like...

Tony


img

Re: Table top attachment questions of ye:

#10

Re: Funny you should ask...

David Best

>Pete I am just north of you in Grand Haven, I used to cut my own blocks for table tops, but I now use the metal brackets.

Shoot me an e-mail and I'll give you enough to try.

Re: Table top attachment questions of ye:

#11

Re: Funny you should ask...

Pete in Holland, MI

>Hey David -

Thanx for the offer. Have seen the little metal clips in the Rockler catalog, but opted last night to make them from wood (I always seem to take the long way around on some of these projects).

Final sanding occured last night of the project. Staining begins tonight.

Hope to be able to post a photo of the table set in a week or so.

Pete