Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Leigh Super jig 12" vs 18"?

Posts

Leigh Super jig 12" vs 18"?

#1

Leigh Super jig 12" vs 18"?

North of the Border

>I am thinking of getting a Leigh Super jig to do through dovetail joints but am not sure if the 12" capacity or the 18" is more suitable. I mostly cut joints under 12" (for drawers, boxes, etc.) and can not quite think of a joint as large as 16" or the like. Does anyone have any views? (Unlike the 18" or 24" model, the 12" one can't do isoloc joints.) Thanks.

Re: Leigh Super jig 12" vs 18"?

#2

Re: Leigh Super jig 12" vs 18"?

Ron Hildreth

>One way to look at it is, if you have many drawers to build, say each 4" deep, the 18" would yield up to 4 sides at a time with minimal set up.

Isn't nice to know you have the added capacity should the need ever arise?

Ron in Iowa

Re: Leigh Super jig 12" vs 18"?

#3

Re: Leigh Super jig 12" vs 18"?

Roger Lance in GR, Michigan

>If you want to make through dovetails, I'd recommend that you not buy a jig...but rather, get a copy of FWW in which Jeff Miller shows a shopbuilt jig for the tablesaw that makes pins and the use of a bandsaw for tails...I've done this and it works extremely well...and you get to keep your hard earned, north of the boarder money.

Re: Leigh Super jig 12" vs 18"?

#4

Re: Leigh Super jig 12" vs 18"?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Woodguy,

I've had to exceed 12" several times. Infant cradle backs and my wife's cedar chest are two examples which come to mind. It would have been nice to have a 18' jig handy. I reconsiled the problem by switching to finger/box joints using my table saw and shop made jigs. It was certainly less costly, gives the "thru" look, and not difficult to do once the jig had been tested and my technique tweeked. I am one of those guys who need tweeking! I do have a 12 inch P+C jig which will do various dove tail styles and box joints. Its also nice to be able to do them either way. If you can, get tghe biug jig. The prices will never be lower.

George

Re: Leigh Super jig 12" vs 18"?

#5

Thanks all for your comments

North of the Border

>Making multiple joints on a 18" jig - that was a good tip ... I was just wondering what kind of drawers one would make that are more than 12". I'd also see if I can find the FW article (does any one happen to have a scanned copy?)

Re: Leigh Super jig 12" vs 18"?

#6

Re: Leigh Super jig 12" vs 18"?

North of the Border

>Thanks. It's issue #120 (Machine Dovetails by Eye

Cut perfect pins on a simple tablesaw jig; finish up with a bandsaw

by Jeff Miller). Unfortunately, access to the article on FWW website is a membership privilege.

Re: Leigh Super jig 12" vs 18"?

#7

Found the article in the this book

North of the Border

>Joinery : shaping & milling : techniques and strategies for making furniture parts from Fine woodworking. I've requested a hold of the book from my local library.

Re: Leigh Super jig 12" vs 18"?

#8

Re: Leigh Super jig 12" vs 18"?

Marc Rosen

>Hey North,

I own a D4R so I am not too familiar with the Super Jig, but if you can use the Super Jig to make asymetrical joints, the wider the jig, the better off you'd be. On my D4R I set it up to cut through dovetails with increasing pins and tails going from the back of my hutch. The boards were 12 inches wide so I was able to set up the fingers opposite each other on both ends of the jig. I don't think the fingers of the SJ separate like those of the D4R but you could still vary the spacing to give that asymetretical effect. To reiterate, my suggestion is to go with the larger jig - more opportunities.

Marc