Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

"Painting" an ugly garage/shop floor...

Posts

"Painting" an ugly garage/shop floor...

#1

"Painting" an ugly garage/shop floor...

Ralph Turney

>...to make it look nice, easy to clean up and to also park my truck in. I live in Socal, so humidity and water coming up through the floor isn't really an issue.

Here's what's up, I'm in the market for a new place, and I'm bidding on a few of places in the same tract that have two car garages. One of them I haven't even seen the garage, one of them is pretty clean, but on one of the three, the garage floor has got two ginormous oil spot with fresh oil still on them. So I'm just trying to be prepared in case the worst place accepts my offer.

Any suggestions on finishes for the floor, so I can move my tools around, park my truck on an still be easy to clean up??? I understand that I'll have to really clean the oil up and if there is some sure fire methods for that I'd be glad to here of them. Figure about 400 square feet of flooring.

TIA

Re: "Painting" an ugly garage/shop floor...

#2

Re: "Painting" an ugly garage/shop floor...

Lee Schierer - McKean, PA

>You can clean oil spills from concrete easily with "Gunk" engine cleaner. Spray it on the oil and soak it thoroughly. Let it set for the amount of time indicated on the can and hose it off. If you can hose it with hot water it works even better usually one to two applications will take care of even years of accumulated oil on the floor.

Lee

Re: "Painting" an ugly garage/shop floor...

#3

JL

Re: "Painting" an ugly garage/shop floor...

JL

>I've used TSP (tri-sodium phosphate) and powdered laundry detergent to clean up oil stains - make a slurry or liquid paste and let it set on the oil stain for a while. Then you have to rinse it well. I haven't tried the Gunk.

Use dilute HCl (muriatic) acid to etch the floor and rinse well again.

Let it thoroughly dry.

I've used a 2-part epoxy paint on garage (and shop) floors. Your roller covers, pans and brushes won't survive the experience.

Re: "Painting" an ugly garage/shop floor...

#4

Re: "Painting" an ugly garage/shop floor...

Ralph Turney

>Thanks for the help. Are there any brands that you can recommend and where to get them?

Re: "Painting" an ugly garage/shop floor...

#5

Re: "Painting" an ugly garage/shop floor...

Joseph Mulherin, Sr.

>Like JL said, use the TSP and laundry detergent mixed up in a slurry, spread it adequately on the spill spot and then use kitty litter to absorb the gunk for easy cleanup. On the nascar tracks they use a similar litter stuff to absorb the spills. Then etch the floor with an acid and apply an epoxy finish bought from Lowes or Home Depot or Menard or any such store.

Re: "Painting" an ugly garage/shop floor...

#6

JL

Re: "Painting" an ugly garage/shop floor...

JL

>Lowes sometimes has the 2 part epoxy paint, I think it is from Quikrete. I've used the high solids 1 part epoxy, but it doesn't hold up as well (though you can get it in colors).

Re: "Painting" an ugly garage/shop floor...

#7

Re: "Painting" an ugly garage/shop floor...

Mark Strang

>Try Epoxy-coat. I've used it a couple of times and it is great. It won't come off with hot tires and is indestructible. It cleans up nicely and since it is 100% solids you can put in "flakes" that they supply with the kit and add aluminium oxide anti-skid particles to keep from slipping in water, etc. In my basement shop I put it on to an estimated thickness of about 8 mils and added a lot of anti-skid material. Even with all of the sawdust that I generate, I still don't slide around. As I get older I don't want to slip and fall into the saw or catch myself on the lathe like I would with paint which is generally sippery with sawdust on it.

The product is not cheap but is far superior to any big box store products and considering that it sometimes requires more than one coat of the other brands it is probably the same cost. I think that their site is www.epoxy-coat.com

Re: "Painting" an ugly garage/shop floor...

#8

Re: "Painting" an ugly garage/shop floor...

Don Orr

>Ralph, you already have good advice on cleaning the floor. I used a 2 part water-borne epoxy paint in my shop. I think it is made by Muralo. I added some special sand meant for adding to paints for traction. It is a very low odor product and went on easily. It is supposedly guaranteed to not lift up even under hot tires. It was about $55 per gallon.

Re: "Painting" an ugly garage/shop floor...

#9

Oil stains - I use a three step process...

Tim Greif - West of Chicago

>My best formula for oil stains is a combo of products. I also have a pressure washer, which I consider to be absolutely necessary for doing this properly. If you don't have one, I suggest renting one for the day. I use the following in the order listed:

  • Gunk GP cleaner/degreaser, much like Lee's Gunk engine cleaner recommendation. Use a stiff scrub brush and let it set a while, but not to the point of drying out. Squirt a little more on if it starts to dry too quickly. Then scrub a scond time after letting it set. Rinse with the pressure washer and let dry a couple hours.


  • Go back and hit any stubborn areas with WD40. Don't be stingy with it and let it set on the area for at least 10 minutes, keeping it wet. You'll be surprised at how effective WD40 is at dissolving oily stuff. Again, use a stiff scrub brush when you apply it and again after you've let it set. Then pressure rinse it again.


  • I then use Dawn dishwashing detergent to remove any of the remaining oil film and any WD40 film left behind. Scrub well and then pressure wash the heck out of the spot.


  • This last step is optional but I like it. Wet the entire floor with the pressure washer. Doing a section at a time, squirt some Dawn on the floor. Then use a stiff floor broom to sorta wash the whole floor section and rinse. Then do a thorough pressure rinse of the entire floor, back to front, pushing the water out with the spray as you go. Then use a rubber squeege to eliminate any remaining standing water areas.



At this point, it'll be as clean as it's going to get. I do this ritual annually in my garage on the few oil spots I get. I've never had the desire to paint a garage floor. After the slab dries overnight, you'll be amazed at how nice the floor looks again.

Follow the advice of others for floor prep for paint.

Re: "Painting" an ugly garage/shop floor...

#10

Whoa --- what happened to the formatting?

Tim Greif - West of Chicago

>When I previewed this, the bullets all looked fine. Now I've got bullets at the last line of each bulleted paragraph. What's up with that?

Re: "Painting" an ugly garage/shop floor...

#11

Re: Whoa --- what happened to the formatting?

John K Jordan

>This is what I see.


img

Re: "Painting" an ugly garage/shop floor...

#12

Re: "Painting" an ugly garage/shop floor...

John in Calgary

>I did our 2 car garage with two boxes of the epoxy stuff from HD. I added a bag of the anti-slip material to each, it works, but is still slipper when there is a slushy layer on the floor.

For cleaning, I found a post on here from Forrest Addy which is quite comprehensive (you can search on my name, I put a link to his older post).

So far, six months of winter haven't caused the coating to lift yet, even when scraping slush and ice off the floor. I did find more standing water after I coated the concrete - it would seem that the snow and slush used to melt, then absorb into the concrete, where now it runs to the garage door and collects/freezes where it runs under the door.

John

Re: "Painting" an ugly garage/shop floor...

#13

Re: "Painting" an ugly garage/shop floor...

Ralph Turney

>Sorry I haven't been able to respond earlier, but I've been kind of busy. Anyway, thanks for all the advice, I'll be able to use all of it...except maybe the advice for the slush and ice on the floor, as I'll be living in Huntington Beach CA. :-)

Thanks!