Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Dead compressor--fix/replace?

Posts

Dead compressor--fix/replace?

#1

Dead compressor--fix/replace?

Tony Sade (Charleston, WV)

>My bought-at-Lowe's DeVilbiss 5 year old 5hp/20 gal oil-free compressor died over the weekend. Worked one day, didn't the next. I can hear something straining to move and the lights in the shop on the same circuit dim considerably when I flip the switch. (I have a dedicated circuit for the compressor; the dimming occured when I moved the thing out from its normal resting place and tried it at a different location.)

Any likely cause that comes to mind based on such little information-anything that tends to go wrong with these? Anything a DIYer can try on his own?

Any recommendations for a replacement? I'm a hobbyist so it will get light use. I use nail guns/pinners/staplers; fill tires; and use a HVLP conversion gun for finishing. Given my small garage shop setup, it really needs to be one of those that looks like a wagon-wheels on the back, handle in front, tank rests horizontally-or something with a similar footprint. The compressor sits under a table which holds my dust collector with a canister that almost hits the ceiling. There's no place else to put it. I really can't spend more than $400 (without having to sleep in the shop).

Re: Dead compressor--fix/replace?

#3

Re: Dead compressor--fix/replace?

Dan Mitchell

>If the lights dim it's obviously drawing current, so it's not apt to be an electrical control issue like the power switch, or the regulator stuck thinking the tank is up to pressure. Assuming this is a belt driven oil type, I'd remove the belt & see if the motor runs on its own, and if so, if the compressor is locked up. Have you kept the oil level up?

I used to have a Craftsman 240 volt compressor, bought about 25 years ago. Used it a lot when I was doing major automotive work. The tank finally rusted through. Since I don't do nearly as much car stuff anymore, I bought a Harbor Freight pancake compressor to run nailers, etc., the occasional air ratchet/impact wrench, etc. Haven't given it rigorous work, but so far so good. Not sure if the one I have would be up to spraying, but they carry a full line of cheap compressors.

When I bought my Craftsman, DeVilbiss was a high quality brand, not sure if this is still the case. HF & others carry a number of electric motors & compressor units, one of which may be adaptable to your Devilbiss, though I have no idea if this would be cost effective.

Hope this helps.

Dan

Re: Dead compressor--fix/replace?

#4

Re: Dead compressor--fix/replace?

Chuck in ND

>Hard to be sure whats wrong with it without seeing it, but my guess is the piston is probably stuck, being that it's a oiless. I don't buy oiless. MAYBE if you call the manufacturer they MIGHT work something out for you, goodluck.

Re: Dead compressor--fix/replace?

#5

Re: Dead compressor--fix/replace?

George@Colonel's Workshop-Havertown PA

>Good Afternoon Tony,

I was thinking that it could be the piston in the air pump. I would remove/disconnect the air pump and see if the motor kicked over. My DeVilbliss Craftsman's pump exploded on me and I had pump parts all over the shop. At that point, the tool was 15 years old, it never had been overly reliable, Sears would no longer provide parts support so I bought another brand and quit Sears for life. If you like yours, see if it is the pump, and contact the manufacturer for a new/replacement pump.

George

Re: Dead compressor--fix/replace?

#6

Re: Dead compressor--fix/replace? *LINK*

Virgil Johnson, Versailles KY

>If you decide to replace it check out the Makita in my "review" below. This thing is a lot of compressor for 250.00.


http://www.woodcentral.com/cgi-bin/messages3.pl?re

Re: Dead compressor--fix/replace?

#7

I agree about avoiding oil-less

Dan Mitchell

>

Re: Dead compressor--fix/replace?

#8

Sears

David Miller from Iowa

>I just (2 weeks ago) bought a "30 gallon" Craftsman compressor $400 regular, on sale for $300 and they gave me another $100 worth of air tools (socket, impact wrench & chisel). The sale may be off, but watch for it again.

This is my 2nd craftsman compressor - first one died after about 12 years - I figured I got my money's worth.

Just like you can never have enough clamps - you can never have enough volume in your air compressor - those small ones are fine for brad nailing.

David

Re: Dead compressor--fix/replace?

#9

Rick L

Re: It's probably fixable

Rick L

>Oilless compressors tend to just just stop working suddenly. Most likely the piston is seized up. I'd pull the top off the head and check that. Usually they are direct drive so they are essentially very simple units. I know from my days of compresser repair it was about $75 for a piston and sleeve in the early 90's for Speedaire and such brands. Shouldn't be to costly.

Re: Dead compressor--fix/replace?

#10

Re: It's probably fixable

dave nichols

>There may be a valve to release the pressure in the cylinder, if the valve fails while the piston is compressing the air the compressor will not start, I've had to replace several on a small craftsman compressor, since I keep a spare now it hasn't failed in over 5 years

Re: Dead compressor--fix/replace?

#11

Rick L

Re: Check valve is

Rick L

>the proper term for it. Could be a combination of several things but I'm betting it's fixable but I have done this for a living.