Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Wiping varnish

Posts

Wiping varnish

#1

Wiping varnish

Joe

>Whenever I finsih a piece of furniture, I have been using J.E. Moser's Polymerized Tung Oil - satin finish. Unfortunetly, they have discontinued the satin finish and as far as I know make only the high gloss version. I have been toning it down with some 0000 steel wool and wax, but I loved that satin finish. Does anyone have any good suggestions?

Thanks

joe

Re: Wiping varnish

#2

Re: Wiping varnish

Dave Mount

>I've grown fond of General Finishes Arm-R-Seal. Semi-gloss is my sheen preference, but that's a personal choice, it comes in three sheens.

2-3 wiped coats give some protection without looking like plastic, but you can also flood it on horizontal surfaces and get a substantial build with terrific leveling and no bubbles.

Best,

Dave

Re: Wiping varnish

#3

Re: Wiping varnish

GarryF

>I have used Bartley's Jell Varnish with great success...I also use waterlox Satin...a little pricey but gives a great finish.

Re: Wiping varnish

#4

Re: Wiping varnish

Ray Binnicker

>Hey Joe,

I've been using Sam Maloof's "home-made" brew for a number of years and really like it. The formula is in his book and is sold by Rockler, but here it is:

1/3 boiled linseed oil

1/3 raw tung oil

1/3 urethane varnish (semi-gloss)

His top coat is:

1/2 boiled linseed oil

1/2 raw tung oil

2 handfulls shredded beeswax

Heat the linseed oil and tung oil in a double boiler (I use a hot plate outdoors) until it just starts to get warm and start mixing in the beeswax. Mine comes out about like peanut butter.

You can make up a gallon of this stuff for what you pay in the store.

Ray Binnicker

Re: Wiping varnish

#5

Latest FWW Article

Thomas Skaggs, Foothills of Mount Level

>I just happened to be thumbing through the latest edition of Fine Woodworking and they have a good article on making a wiping varnish. I haven't tried it but I intend too. Check it out if you get a chance.

Tom

Re: Wiping varnish

#6

Re: Wiping varnish

jerry mayfield

>You can easily make your own wiping vanish,start with about 50% each of your favorite varnish(any gloss) and mineral spirits. Tweak to suit. Three coats of wipe-on is about the same as one brushed coat.

Regards

Jerry

Re: Wiping varnish

#7

Re: the recipe I use

Glenn Madsen, SF Bay Area

>after gumming up the 1/3 of this, 1/3 of that, and the rest of something else, is:

Take a squirt bottle. Fill it half full of McCloskey's Gloss Spar Varnish.

Add about half that much VMP Naptha to it.

Shake.

Squirt it out onto a clean pad, and wipe it on.

You don't need to be a chemist, and you don't fool with the work of good chemists at the plant, either. Dead easy.

I have too many other ways to screw up nice looking woodwork.

If it needs less gloss, I rub it down with a synthetic white pad and wax after the last coat.

Re: Wiping varnish

#8

Re: Latest FWW Article

Steve Schoene

>There are a lot of aspects of that finish in FWW that give me questions I can't answer.

First, how can adding raw Tung Oil increase the water resistance. Sure tung oil as an ingredient in varnishes aids in producing a varnish with good water resistance, but this is just making an oil/varnish mix.

I suppose the Klean Strip Japan Dry does have some impact on Tung Oil, but I don't think all do. And, the amount used is over twice that given by Klean-Strip as the maximum to use. I suppose with so much drier, the Tung Oil is necessary to keep the varnish from getting so brittle that is crazes, but is this a true balance, or a relatively short term effect that could bite 10 years down the road.

Frankly the act of thinning the varnish and applying such thin wiped on coats gets it "out of the dust" just about fast enough. If it's slow enough drying to apply by hand, it's going to pick up enough dust that some rubbing is going to be necessary for just about every thing except shop jigs--and I don't often put finish on them.

I'd like more assurance that the chemistry really works out OK and some longer term or systematic testing.

Re: Wiping varnish

#9

Roll your own

David Yoho

>I might be missing something but I haven't found anything wrong with wiping on the various Waterlox finishes I've used - straight from the can. Why should I mess with something I'm sure has been formulated to work a certain way?

Other than sometimes using a solvent to thin or that will flash off quickly, I just don't see any good reason to mix up my own brew. I'm happy with the results I get from Waterlox when I want a varnish finish. Arm-R-Seal is another good finish right from the can. No need to change what already works

David