Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Razor sharp chisel - the FW sand paper method

Posts

Razor sharp chisel - the FW sand paper method

#1

Razor sharp chisel - the FW sand paper method

North of the Border

>The FW #184 (June 2006) issue carried an article on sharping chisel with wet dry sandpapers. I finally had a chance to use it method to sharpen my chisels and the result was very satisfactory. I started with a waterstone and then proceeded as outlined in the article using my shop scrap sandpapers. Here's a pic showing the microbevel. I also this approach for sharpening my Flexcut carving knife (the sandpaper method is demonstrated in Everett's Beginning Carving DVD).


img

Re: Razor sharp chisel - the FW sand paper method

#2

PS to Razor sharp chisel - the FW sand paper meth

North of the Border

>I began with waterstone because the chisels were poorly maintained, to start with. The sandpaper method doesn't require the use of waterstone if the tools are in reasonable conditions.

Re: Razor sharp chisel - the FW sand paper method

#3

Re: But, Mr. Border

Al Stokka - Cambridge, Iowa

>or should I call you "North?"

The cutting efge of your chisel is curved. Did you hold the chisel freehand?

Al

Re: Razor sharp chisel - the FW sand paper method

#4

Re: But, Mr. Border

North of the Border

>You have an eagle eye! As I said, these chisels were poorly maintained and out of squareness, to start with. They are scrap chisels that I used to test out the FW method. I didn't spend anytime trying to square them off in the first place. Now with sharp edges, I will use them for roughing work and save my well-tuned (and more expensive) chisel set for more delicate and detail / finishing cuts. The experiment with its satisfactory result in achieving sharp edges, however, will allow me to use the sandpaper method for my finer tools.

Re: Razor sharp chisel - the FW sand paper method

#5

Re: But, Mr. Border

Al Stokka - Cambridge, Iowa

>Good idea to practice on the old tools. I have a mortise chisel that I sharpened with the sandpaper on plate glass method. It's my only really sharp chisel and I don't use it often. Wouldn't you know, the first time I picked it up to use it I sliced my finger open.

Be careful if you sharpen your tools!

Al

Re: Razor sharp chisel - the FW sand paper method

#6

I guess as they say: Scary sharp!

North of The Border

>

Re: Razor sharp chisel - the FW sand paper method

#7

Re: Razor sharp chisel - the FW sand paper method

Alexander Grigoriev

>I'm using 3M microfinishing film (sold by Lee Valley) with great success. First 15 micron; you'll want to use some contact spray glue to affix it to glass (spray on the film only, let dry 5 minutes, then roll down with a dowel). You can use oil on it. When lapping the chisel's back, though, NO OIL.

Then 5 micron film. It will hold to the glass by itself; make sure there is no dust or dirt - use a razor to clean the glass. Wipe glass with mineral spirit; then wipe it almost dry. Roll the film with a rubber roller; make sure no air bubbles. You can use a little bit of oil on this film, too.

Finally, 0.5 micron chromium oxide film. Affix it the same way as 5 micron film. You can use trace amount of oil for lubrication: dip a finger; smear it around, then wipe dry.

Re: Razor sharp chisel - the FW sand paper method

#8

Re: Razor sharp chisel - the FW sand paper method

Jay St. Peter - Southern, MD

>I've been using sandpaper for a number of years and finally bought some water stones last week. The grass is always greener I guess.

Jay