Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

HVLP Spray Gun...

Posts

HVLP Spray Gun...

#1

HVLP Spray Gun...

Rob Hix - King George, VA

>Just wondering if anyone here has tried either of these HVLP guns from Harbor Freight:

Option 1 at $30.00 I am thinking even if it is trash it should be good for something.

Option #2, coming in at $60.00, I can really not tell the difference in this and the previous gun, except the air volume requirements are a little different. I could see how a gun that uses less air would cost a little more.

Finally, Option #3, The cup on this one is only 5.3 oz, which I think would be a pain in the rear except for a very small project.

I am about done with a set of bunk beds, and I need to paint some of them. I am using latex paint. I have read a couple of reviews online that say these guns do a good job for the price. Just wondering what experience everyone had had with them.

Thanks for the input,

Rob Hix

Re: HVLP Spray Gun...

#2

Re: HVLP Spray Gun...

Larry Clinton At Frankfort (Central)., Indiana

>Rob, I have the gun shown in your option 2 - I purchased it for $20 during one of theie sales. You may want to wait for the sales as they have this on frequently. I did use it to spray oil stain on some birch plywood, did a pretty good job. I also bought another HVLP gun from them (the one with the aluminum quart container that screws on under the gun) when it was on sale for $19.95. Haven't tried it out yet. I thought I might use them in the shop for small jobs. Most of my spraying is done with a conventional Binks standard (automotive type) spray gun. It does a wonderful job, but is wasteful of the finish material and can't be used in my closed shop for any job. Sorry I can't be more help.

Re: HVLP Spray Gun...

#3

Re: HVLP Spray Gun... *LINK*

Rich Glisson

>I have not tried those, but have used the Wagner conversion gun extensively and can vouch for it. Gleem paint is selling it for $129 (see link) and it is also available from Amazon and other sellers.

I sprayed all of the trim and kitchen cabinetry in our large, trim-intensive house with 3 coats of Sherwin Williams ProClassic acrylic using this gun. I also bought a second gun for the oil-based primer that I used.

I had to thin the ProClassic 10-15%, and there **IS** a learning curve.


Wagner conversion gun

Re: HVLP Spray Gun...

#4

Re: HVLP Spray Gun...

pecker

>I have #3 and #1.

The detail gun is only good for shellac or thinned polyurethane, and small projects at that.

Item #1 might spray the latex if it's thinned substantially, but requires a lot of air. Something bigger than just a 15 gallon tank compressor.

Re: HVLP Spray Gun...

#5

Re: HVLP Spray Gun...

Jay St. Peter - Southern, MD

>I've heard good things about your option 2. But, I really have no experience with those guns. I'm just going to comment on what I have read about spraying with HVLP. One thing I've read is that latex paint is tough. You may want to reconsider the finish choice if you want to get into HVLP. I used Target USL tinted blue (homesteadfinishing.com) to spray the beds for my kids. I was trying to mimic a pottery barn finish and was successful. The stuff has proven pretty darn durable as well. I have two jet sizes for my gun depending on the type of finish I'm spraying. One for water based and one for solvent based ... basically. I don't think either would spray latex without some serious thinning, but I haven't tried. I'm just judging by the viscosity of what I have successfully sprayed with each. OTOH, you may want to watch the latest video at thewoodwhisperer.com where he tries a new HVLP system and says it sprays latex OK. Also important are the CFM ratings for each gun depending on your compressor. Some use some serious air and others are pretty easy to satisfy. Even with a low-end 60gal compressor, I was advised not to choose air hungry guns.

Jay