Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Anybody have Collet Problems on the P+C 690?

Posts

Anybody have Collet Problems on the P+C 690?

#1

Anybody have Collet Problems on the P+C 690?

George@Colonel's Workshop-Havertown PA

>Good Evening Friends,

Bad weekend thus far. Ive been making eight drawer boxes with my P+C 690 and P+C 4212 jig. The dovetail bit seems to be tight in the collet, but most certainly slipped enough to ruin several of the pin boards. The set ups are fine, and the prototype drawer box pieces mate together with congeniality. I've ruined three or four pin boards, and will install another collet from another P+C router. The 1/2" collet in question seems perfect under inspection. It has been used nearly day for 10 years or more, and never gave one lick of trouble. I've not abused it, but realize nothing is forever. However, I've never read about one of these animals ever failing.

Is there anyone out there who has experienced a similar problem? Comments, please.

George

Re: Anybody have Collet Problems on the P+C 690?

#2

Re: Anybody have Collet Problems on the P+C 690?

Joanne Adler in Pt. Pleasant, PA

>Frank says to cut 'em by hand! };->

Re: Anybody have Collet Problems on the P+C 690?

#3

Re: Anybody have Collet Problems on the P+C 690?

Carol - now in NC Nebraska

>They do wear out, George.

But before you scrap it, clean it thoroughly. And clean the socket it fits into. It has been my experience (especially when teaching) that a dirty collet/socket allowed the bit to change depths.

That doesn't work, get a new one. Should be less than $20. You deserve it. If it hung in there for continuous use for 10 years, it's done it job quite well.

Re: Anybody have Collet Problems on the P+C 690?

#4

Re: Anybody have Collet Problems on the P+C 690?

Robert R clough - Thorncraft

>George, I have two 690s. Once in a while a collet does slip for me. Each time, however, I found I had not raised the bit enough - less than 1/8". Thus the bit rode up. (I always mark my bits with a line for depth - but sometimes I forget to use my markings.)

The other possibility is dirt in the collet. Periodically unscrew the tightener, take out the collet, clean out the collet holder, and the back to work. Oh yes, be sure the bits are clean as well.

Other than that, I don't know!

(For me cutting by hand takes far too long and is an exercise in frustration!!)

Re: Anybody have Collet Problems on the P+C 690?

#5

Careful what you ask for...

David Yoho

>I'm thinking Frank didn't think before he said that or he would've given a different opinion.

Think about it - - people put down their routers today and start cutting dovetails by hand and the next thing you know they lay down their tablesaws and begin using hand saws, then tomorrow a jointer is given its pink slip and replaced by a hand plane!! All those poor, unhappy, unemployed power tools sitting around the burn barrel under the city bridge wishing for the good old days.... It's just too frightening to imagine!!!!

Re: Anybody have Collet Problems on the P+C 690?

#6

Re: Careful what you ask for...

Joanne Adler in Pt. Pleasant, PA

>Frank says, ";-)"

Re: Anybody have Collet Problems on the P+C 690?

#7

Re: Anybody have Collet Problems on the P+C 690?

Larry Clinton At Frankfort (Central)., Indiana

>Can't say as I've had any problems with either of my 690's or my 7539 (same collets) slipping or sticking. However, I do have a tendency to over-tighten everything. Maybe you just didn't lean on the wrenches hard enough Colonel! I have had my old Crapsman and an old skill router collets slip. Gave the Skill away with a warning about the collet. Still have the Crapsman - haven't used it in a couple years - may give it to a friend. I do keep my collets and Router shaft pretty clean & am careful to keep the router bit lube off the shank.

Re: Anybody have Collet Problems on the P+C 690?

#8

Only a Jersey Girl can curse like that.

Art Silva

>

Re: Anybody have Collet Problems on the P+C 690?

#9

Thank You All, Including Fred

George@Colonel's Workshop-Havertown PA

>Good Morning Friends,

I took everybody's advice and examined the collet and base again, and then cleaned it thoroughly using CMT bit cleaner and paper towels. The socket in the base of the collet shaft had more sand than the Sahara. The inside of the collet came clean and shiney brite. Not withstanding, I swapped the collet from my P+C 7518, cleaned it, and put that on the 690. Carol, I think I'll acquire a replacement collet this coming week. The cost of a replacement is minimal, and the cost of lost stock and time was significant. The ruined material can be trimmed and used as back ups in the jig. So, all was not lost.

George

Re: Anybody have Collet Problems on the P+C 690?

#10

Sand?! Is this another camel story?! :-)

Joanne Adler in Pt. Pleasant, PA

>

Re: Anybody have Collet Problems on the P+C 690?

#11

Sure it is, Now That I'm Over The Hump

George@Colonel's Workshop-Havertown PA

>