Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Chair Seat Carving

Posts

Chair Seat Carving

#1

Chair Seat Carving

Paul Leuba

>I intend to make a few Windsor style chairs and need to purchase the tools used to carve the seat. My current thinking is to use an adz to rough out the bowl, and a large gouge to smooth out the rough work of the adz. What should best be used for the next step to smooth out the carved bowl?

It does not appear to me that a random orbital sander would be aggressive enough and the more aggessive chain saw type carving tools that fit on a 4" angle grinder seem very dangerous.

Do any members of the forum have experience with the carbide carving disks advertised for 4" and 4 1/2" angle grinders, or can you offer advice on the best overall way to approach this task?

Paul in Hunt Valley

Re: Chair Seat Carving

#2

Re: Chair Seat Carving

Kneale Brownson enjoying snow in N. MI

>Here's a paragraph from a description of a Windsor chair class that's in the BP archives on Woodcentral:

The seat edge was shaped first using drawknife and spokeshave. The seat was then "saddled" or dished out using in succession, a gutter adze, a scorp, a travisher and compass plane. The gutter adze is a fierce looking tool that roughs out the saddle and removes lots of wood chips in a very short time. A scorp is a convex shaped drawknife that smoothes out the chopped surface left by the adze. The travisher is a tool uniquely designed for chairmaking and is essentially a convex soled spokeshave. The compass plane also has a convex sole and was used together with the travisher to finish the saddle shaping. One had to keep sight of the wood grain using all these tools; approaching from the wrong direction could result in a nasty gouge or unwanted chip. The final finishing touch to the seat was cutting a long curved 1/4" wide groove or "rain gutter" along the edge of the dished area. The groove is a design feature serving to separate the flat edge region where the spindle holes are drilled from the center saddled seat area. This groove was cut freehand using a veining tool carving gouge.

Re: Chair Seat Carving

#3

Re: Chair Seat Carving

Clint Searl, at the base of Haycock Mtn

>I have the Lancelot chain saw disk and its less aggressive brother. After a little practice they are easy to use and control. Either will waste a lot of wood with precision. They're worth the investment.

Clint

Re: Chair Seat Carving

#4

Re: Chair Seat Carving

Philip Duffy

>If I may add to the discussion; the scorps one buys have a very poor cutting profile and as soon as I re-ground mine to a sharper edge profile the whole process became easier, by a bunch. I have a scorp that is razor sharp and it is my primary tool for scooping out the seat pans. I do not own a adz and do not want one as the effort and strain on my back would be too much. The real key seems to be to get down about an inch from the flat at the back of the chair seat and then work around to where the legs absorb the wt. of the person. Good luck!

Re: Chair Seat Carving

#5

Re: Chair Seat Carving *LINK*

Moses Yoder in White Pigeon, MI

>I have the Veritas pullshave which I have messed around with some and it's a great tool. The advantage to a tool like this over the carving wheels that you would attach to an angle grinder is the amount of control you have over the cut. My own personal opinion if you are carving a few chair seats this would be the tool to use. You can remove a lot of wood in a hurry working across grain with very controlled cuts.


Veritas Pullshave

Re: Chair Seat Carving

#6

Re: Chair Seat Carving

Paul Waddle

>Take a look at this router carving set up: http://wwww.woodweb.com/knowledge_base/A_Router_Duplicator_for_copying_Curved_Shapes.html. This gent made it just for the chair seat operation.Looks like four double row Thompson ballbushings of 1" and the corresponding hard shafting. (maybe a tad expensive-might try substituting delrin or bronze bushings and ground cr steel shafting). pw

Re: Chair Seat Carving

#7

JL

Re: Chair Seat Carving *LINK*

JL

>I've used the Lancelot (and I have one) and the Tungsten Carbide Grinding "Donuts". I like roughing out with the Lancelot and then using the "Donuts" to smooth out the chain saw marks. I then switch over to 24 and 36 grit abrasive disks. This is all done with the angle grinder.

After I get it "roughed out", I then use a pull shave (Veritas) and spoke shaves. I've done it with adze and scorp a couple of times. It's a bit nerve wracking seeing the splinters fly :).


Tungsten Grinding "Donuts"

Re: Chair Seat Carving

#8

Re: Chair Seat Carving

Paul Leuba

>Thank you, everyone, for the feedback. These messages have given me some great ideas to pursue. I like the idea of the adz and the scorp to rough out the seat, and then come back with the angle grinder with course grit disk and the Veritas pullshave to clean it up.

Thanks again!

Paul in Hunt Valley