Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

OT: Removing wooden siding

Posts

OT: Removing wooden siding

#1

OT: Removing wooden siding

Dan Mitchell

>I've posted here a couple times about issues related to rats in the crawl space of the house we bought a year ago. I've been trying to address every possible entry point, and have eliminated several. While doing some wiring down in the "dungeon", I noted light coming in around where the siding/sheathing meets the poured wall. Below are 2 exterior pictures. The area is a corner, adjacent to the brick fireplace on the left, and is confounded a bit by the concrete base of a chain link fence post on the right. The holes are on the right, beneath where the copper mesh is inserted (a material a bit like a scotch-bright pad made expressly for plugging rodent holes) at the end of the siding. I would like to remove the siding & sheathing in this area, over to the fireplace & up to the 1st full length board, replace the existing sheathing (it's that soft, dark brown fiber-board like material) with something a bit more robust, maybe add some additional framing timbers, etc., just generally seal off the area, then replace the siding. The exact approach will depend on what I find when I get the siding/sheathing off. Anyway, I've never removed siding before, and before I just go out & start prying away, I thought I'd see if anyone here has any suggestions. For instance, should I start by prying off the 1st shorter board under the full length one, or begin with the lowest board? Or is some cutting required 1st?

Thanks,

Dan


img

Re: OT: Removing wooden siding

#2

Re: OT: Removing wooden siding

Barry Irby

>Dan,

That appears to be cedar siding. In fact I think I have some identical stuff on my house.

It is likely to be brittle and tender, easy to break. It should be nailed through the siding so that the nails are near the bottom edge but so that they only penetrate one piece. This is supposed to allow the pieces to expand and contract with changes in MC and "telescope' in and out under the lip of the upper piece.

I think you will find a lot of it is "glued" together with the paint. I would remove or cut the bottom row of nails and carefully cut the paint holding the pieces together. You might be able to use a block of soft wood on top of the shoulder and whack it sharply with a hammer. The shiplapped edges are thin and brittle. Be careful.

When I do this I put a metal cutting blade in my Sawsall and slide it up under and cut the nails. When I reinstall the siding, I use aluminum nails with larger heads to fill and cover the old nails holes.

As an aside, It appears to me that the siding is too low to the ground. There should be some ground clearance (6")to reduce the possibility of termites and rot. You might be able to improve the situation by using Hardie plank or some other rot resistant material for the bottom courses. Hardie Plank comes in a wood grain pattern that would probably blend rather nicely and will not rot and is not attractive to termites.

There is another reason for the ground clearance and that is to give the owner and opportunity to observe the termites mud tubes before they have a chance to eat the house. With the siding too low, they can slip behind it and molest the house at will. Consider finding some long lasting termiticide and treat the area behind the siding.

Re: OT: Removing wooden siding

#3

JL

Re: OT: Removing wooden siding

JL

>If you can find a "roofing" prybar or a sturdy flat prybar (something like the Stanley Wonder Bar), that may also help pry up the siding.

Re: OT: Removing wooden siding

#4

Re: OT: Removing wooden siding

George Koch

>Dan, It might be my eyesight, but in the photo it appears to me that the siding runs behind the brick fireplace. If that's the case it's going to require you to cut the siding at that point or somehow remove it from behind the brick and then reinstall new behind there as well. George

Re: OT: Removing wooden siding

#5

Re: OT: Removing wooden siding

Dan Mitchell

>Barry - Thanks for the detailed response, I see what you mean. The sawzall sounds like a good approach, along with a utility knife to cut through the paint.

On the sheathing, this is probably a dumb question, but is there any reason I can't use plywood of the same thickness as the existing fiber board?

On the wood being too close to the soil, you should have seen it before I pulled 3-4" of dirt back! ;-) When I get this apart, if the concrete goes up high enough, I may not replace the siding on the lower portion. If not, I'll look into the hardie board. This is on the rear side of the house by the trees, so appearance isn't TOOOO critical.

Thanks again,

Dan

Re: OT: Removing wooden siding

#6

Re: OT: Removing wooden siding

Dan Mitchell

>Thanks JL, I do have a number of thin prybars that should work well.

Dan

Re: OT: Removing wooden siding

#7

Re: OT: Removing wooden siding

Dan Mitchell

>George-It does look like that, but the siding doesn't go under the brick.

Thanks for your reply.

Dan

Re: OT: Removing wooden siding

#8

Speaking of termites

Dan Mitchell

>My last house in Ohio had them. They did a bit of damage before I discovered them (umm, what are all those winged ant things pouring out of that outlet cover... ) but not too much. I know the mud tubes you're referring to. Most remarkable thing: the way they would eat the paper off the interior surface of the drywall, leaving the paint in place. A bit ripply looking, and the paint would fall away easily once you noticed & started poking, but still looked reasonably presentable.

Very considerate of them, I always thought.

Dan

Re: OT: Removing wooden siding

#9

Re: Speaking of termites

Barry Irby

>Dan,

You certainly could replace the Sub-Siding. (Storm siding, Sheathing, Whatever its called in your neighborhood).

If its the fiber board stuff it may be the product sort of generically known as "black fiber board". The fibers may be a by-product of making sugar from sugar cane. They are actually brown. The black part is a sprayed on tar coating to give it water proofing. There is a possibility that it serves as part of the bracing of the walls against "racking". There are two versions of the fiber board, Regular and Intermediate. If the regular is used, they should have put plywood on the corners for bracing. If the Intermediate is used and it was thoroughly nailed, you don't have the plywood on the corners.

If I were doing this locally, I would go to the Borg and buy 1/2" pressure treated plywood and use that. They have it in stock. Be sure to use heavily galvanized nails or screws rated for treated wood. Also, you want to seal the joints. The joints should fall on the studs and plates, so that none of them are open cracks into the framing cavities. There is tape that is available to seal the joints if you cut and replace the siding. (this will cut air infiltration and make it less attractive for pests.) The Borgs should have suitable tape. (About three inches wide and sort of soft and gooey)

Speaking of termites..... A friend in college many years ago bought an art print and had it framed. The print was a couple of hundred bucks, a fortune in those days. It hung on his wall in a place of honor. The only decent thing he had (except for that coffee table made from a big wire spool). At the end of the year we were moving him out only to learn that termites had come out of the wall and gotten into the print, and eaten the paper, leaving nothing but the ink. The picture fell part like an Etch a Sketch picture. One of life's weird sad funny moments.

Re: OT: Removing wooden siding

#10

Re: OT: Removing wooden siding

Darylee

>I'd use a small circular saw so you can regulate the depth.

You don't want to cause more problems.

Then, use a hand saw to gut through what the circular saw doesn't cut.

A utility knife will go through the backer board..ist's sort of like cardboard..

Look to new construction sites in their scrap bins for some the size you need. Do not use plywood. You want the flexibility of this backerboard.

Remember as all things, less is more.

Your situation, been there, done that....got to the other side of teh garage and ended up pulling the whole lot down and putting new up, but then I have that press board siding there...different than on the house.

Re: OT: Removing wooden siding

#11

Re: OT: Removing wooden siding

Darylee

>ONLY AFTER CUTTING ABOVE.

You'll end up prying off more than you want.

Re: OT: Removing wooden siding

#12

I understand, Thanks Darylee

Dan Mitchell

>

Re: OT: Removing wooden siding

#13

Re: OT: Removing wooden siding

Dan Mitchell

>Not sure I'm following you on the plywood/flexibility issue, can you elaborate?

Thanks,

Dan