Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Flower Inlay Help Needed

Posts

Flower Inlay Help Needed

#1

Flower Inlay Help Needed

Ken Bellock (Houston, TX)

>I need some help with this one. I'm trying to do an inlay of the pattern shown in the posted picture. I would like to inlay this on some couch side tables I'm making, and several other projects coming down the pipe. My wife loves this flower and especially this pattern of the flower. I know I can do it by hand, with a marking knife, chisels, some other small tools and a lot of time. But it looks like I'm going to be inlaying this pattern a lot and am looking for a faster way to do it. I have a router inlay kit, but the problem with that is all the tight "V" areas, and their proximity to each other. The outer collar of the inlay kit is 9/16ths, and needs to be able to travel within all the grooves of the template. Even with creating a separate template for the stamen, and rounding off all the points to 1/8", I can't figure out how to make a pattern that will work with the inlay kit. Maybe a separate pattern for each petal of the flower, but then I think that wouldn't be saving me much time with all the pieces involved. Please tell me I'm missing something, that there's a neat trick I don't know about, or another technique I can use besides the router inlay kit. Ideally the inlay would look just like this image, and be under 3" on it's narrowest side. I have tried changing the pattern to something I can make a template of easily, but my wife keeps saying she likes THIS pattern.


img

Re: Flower Inlay Help Needed

#2

Re: Flower Inlay Help Needed

Steven Mellott

>Ken:

I don't know of any neat trick, but you can do this type of inlay with a scroll saw.

Re: Flower Inlay Help Needed

#3

Re: Flower Inlay Help Needed

Henry (Raleigh NC)

>Caveat - I have NO experience doing this.

As you state, separate templates would work, but be time consuming. I think that by choosing the areas appropriately you might be able to get away with using only two templates that can be aligned. One template cuts one side of the tight feature, and the other template cuts the other side. Assuming the white is the area that stays and the blue is routed away, I can see this working for all features except the top right area towards the pistil or stamen (I forget my flower parts). That feature looks very tight for all but the very smallest router bits.

Henry

Re: Flower Inlay Help Needed

#4

Re: Flower Inlay Help Needed

Keith Newton, LR, Arkansas------WebKitFormBoundary

>Have you thought about taking your parts to someone with a laser engraver? They may be able to cut both the mortise, and the inlay parts.

Re: Flower Inlay Help Needed

#5

packet cutting *LINK*

tek-Brunswick, Ohio

>Steve is right you can cut the parts with a scroll saw using packet cutting technique. Search marquetry and packet cutting and you should find some resources. Paul Schurch covers it in his marquetry video. I bought Paul's videos and found them very helpful. Basically you stack up the different color veneers for your project. Put them between a couple of layers of single ply cardboard to form a packet. Fasten a copy of the pattern to the top of the packet and cut all pieces out with a scroll saw using an 0/2 scroll saw blade. The packet can be held together with tape and or brads. The brads need to be out of the cut lines. I use a 23 Ga. pin nailer and bend over the brads top and bottom to act as staples. With the 23 gage brads the holes seem to disappear after assembly. I think the water from the glue swells the fibers back into the holes. After you cut everything out the pieces go together like a puzzle. The 0/2 saw blade is very thin and makes acceptable joints. After you have your flower in a background veneer you can . Make a round or oval pattern and insert the whole piece using your router inlay templates. The picture I posted is a combination of packet cutting and knife cutting techniques. I'm just starting down the path of inlay and Marquetry, but I am enjoying it .


img

Paul Schurch

Re: Flower Inlay Help Needed

#6

good point

tek-Brunswick, Ohio

>Most, if not all, of the commercially available marquetry inlays are laser cut.

Re: Flower Inlay Help Needed

#7

Re: Flower Inlay Help Needed

Ken Bellock (Houston, TX)

>Meetings keep pulling me away from all the excellent responses. Thank you for posting all your thoughts. If I didn't have to burn 40 hours a week in this office I wouldn't have to try to find faster ways of making this inlay! Of course, then I couldn't afford the tools to do it either... Anyway, to the ideas that have come up so far. Finding someone with the laser equipment, or outsourcing it, is out. I enjoy doing it myself too much. I'm just trying to cut down on the time it takes me. Using a scroll saw to put the pattern in an oval or round background, and then using the router to inlay that is a fantastic idea. I just don't have a scroll saw yet. This is definitely a technique I will pick up in the future, but I would like to find a solution with my currently available tools if possible. If I have to give up with the router, any suggestions on the brand, make, or model of the scroll saw? Thanks again for for all the suggestions!

Re: Flower Inlay Help Needed

#8

Re: Flower Inlay Help Needed

Dan Donaldson

>You could cut them out by hand with a fretsaw. I did a bunch of pearl inlays that way. I cut them out with a fretsaw, then cut the mortises using a dremel with a base to hold it up. Those bits are small enough to cut out most of the detail you have.

Re: Flower Inlay Help Needed

#9

Mini CAD/CAM system

Mark Goodall - ATL - tooljunkie

>Two thoughts came to mind. The Laser mentioned earlier and that mini CAD/CAM system mentioned here a few weeks ago (name escapes me at the meoment) The one that looks like a lunch-box planer but has a mini-router inside.

Or how about sand blasting? Cut out the pattern in some light gauge steel sheet and use a cheap sand blaster with a compressor.

How many are you planning on doing?

Happy Woodworking!

Re: Flower Inlay Help Needed

#10

Re: Flower Inlay Help Needed

Ken Bellock (Houston, TX)

>I was considering doing it this way for a while, but was worried about the dremel getting away from me too much, and there being big gaps.

Re: Flower Inlay Help Needed

#11

Re: Mini CAD/CAM system

Ken Bellock (Houston, TX)

>The carvewrite is what you are refering to I believe. Been eyeing that one for a while wonding if it's worth it. The price is steep just for the unit, and I see lots of problems mentioned in the reviews I've looked up. I will probably get one after they go through a couple of generations of improvements. I'll be doing at least 20+ of these, potentially many more. The sandblasting idea sounds fantastic! Never thought of that. I'll run to the borg tonight and pick up the attachment for my compressor. I really want to make a test run on some scrap and see how it turns out. Thanks for a fantastic idea. I think the inlay would look much nicer on a couple of my projects, but this would be perfect for several places on the tiki bar I have been tasked to build for the wife.

Re: Flower Inlay Help Needed

#12

Re: Flower Inlay Help Needed *LINK*

tek-Brunswick, Ohio

>I have the DeWalt Scroll Saw. I bought that on the advise from some people that sell Scroll Saw work at craft shows. I have been happy with it. I don't have anything to compare it too except an old craftsman spring top scroll saw I had. The spring top didn't have that much blade tension and you needed a tool, an allen wrench if I remember right, to change blades. With my DeWalt I don't need tools to change the blades and the tension and speed controls are easily reached. For cutting packets of veneer almost any of the available new saws should work. You can do packet cutting with a fret saw, but it takes more time, and it takes more skill to hold the saw perpendicular to the work. There are also plans for making a hand powered scroll saw or Marquetry Donkey. I have not tried any of them. Here is a link to B & B Rare Woods. On the online store page you can order plans for a hand powered scroll saw. They are a good source to buy veneers from and nice to deal with.

There are other plans for making a Marquetry Donkey out there if yoiu search.


B & B rare woods

Re: Flower Inlay Help Needed

#13

Re: Flower Inlay Help Needed *LINK*

Dan Donaldson

>I have a little base that makes it kind of like a tiny trim router. It is actually pretty easy to control. The inlays in the attached shop shot were done this way.


Inlays

Re: Flower Inlay Help Needed

#14

Re: Flower Inlay Help Needed

Ken Bellock (Houston, TX)

>Are you talking about the plunge router base for the dremel? Do you think the Bosch Colt with a 1/8" spiral bit would be comparable for this use, or too big?