Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Zinsser SealCoat

Posts

Zinsser SealCoat

#1

Zinsser SealCoat

John Pappas

>A couple years ago I purchased a can of SealCoat. After a short time the can developed pinhole leaks in the bottom and leaked on the the shelf. No problem. I got a new paint can from HD and transfered the stuff. Again, pinholes soon developed. I mentioned this to a clerk at my local Rockler store. Strange, but he had experienced the same problem. I call the 800 number at Zinsser. They did not say anything about similar problems, and sent me a coupon for a free gallon of SealCoat. Being gun-shy I placed that gallon container inside a plastic pail. I have used some previously without problem. Today I started a finishing project and .......pinholes and leaking shellac in the plastic pail.

Before I contact Zinsser again I thought I'd ask if anybody here has had any similar experience.

Re: Zinsser SealCoat

#2

Re: Zinsser SealCoat

Wess in NJ

>Yep, I had the same problem with the last two gallons.

Re: Zinsser SealCoat

#3

Re: Zinsser SealCoat

David Yoho

>It's happened to me a few times. I buy it by the quart and two different cans leaked.

David

Re: Zinsser SealCoat

#4

me too (quart size)

Mike Hamilton

>

Re: Zinsser SealCoat

#5

Re: Zinsser SealCoat

Steve Schoene

>Shellac is acidic and can react with metal--metal containers can cause shellac to darken snf become cloudy. I'm surprised that the acidity would be sufficient actually corrode the metal enough to break through. The cans are supposed to be coated to prevent that reaction, and I'd suspect some quality control problem on the can lining.

Re: Zinsser SealCoat

#7

Louie Lovas

Re: Perhaps...

Louie Lovas

>This happened to me about a year ago, big splotch of hardened shellac on the concrete in the back room of my shop, aarrgghh. This was a gallon can of the stuff. Now I transfer it to a plastic container after I buy a new can.

Re: Zinsser SealCoat

#8

I agree....

Howard Acheson

>... that is sounds like something is damaging the coating on the inside bottom of the can. I only stir finishes with wooden stirrers.

Re: Zinsser SealCoat

#9

Re: Zinsser SealCoat

Joe in Tallahassee FLA

>I've had the same problem. Like Louie, I now put it in a plastic bucket.

Re: Zinsser SealCoat

#10

Not by stirring

John Pappas

>Doesn't need to be stirred. This is not the cause.

Re: Zinsser SealCoat

#11

Re: Not by stirring

Howard Norman

>>Doesn't need to be stirred. This is not the cause.<

That doesn't mean that people are not stirring SealCoat.

Re: Zinsser SealCoat

#12

Where's Michale Dresdner when you need him?

Tim Greif - West of Chicago

>I have a five year old can of SealCoat on a shelf that's probably half full. (I know, I should toss it after three years but it still seems fine) No leaks on that one. However, I have had Zinsser BIN develop pinhole leaks on the bottom of the can as the other posters have experienced. But that was over ten years ago. I assumed it was because I stored it on a metal shelf, although no other cans developed leaks. I still wonder why.

Re: Zinsser SealCoat

#13

Re: Not by stirring

Brian D

>I don't stir mine and I've had the same problem. Glad someone spoke up because I wondered why/how this happened. I have another can on the shelf, better get that can taken care of before I have double the mess!

Sounds like a Zinsser QC problem.

Re: Zinsser SealCoat

#14

I'm here, and here are some answers

Michael Dresdner

>Steve and others got it right. Shellac is indeed acidic enough to eath through steel cans, and for that reason, the cans are lined with epoxy. As some folks pointed out, stirring SealCoat is not necessary, and stirring with metal (I know some people stir with the screwdriver that is in their hand because they just opend the lid with it) can also scratch the thin epoxy lining and cause the problem.

Companies like Zinsser buy their cans from a supplier, and at times, there are voids in the epoxy liner that can result in the pinholes you are seeing. Since they buy large batches at a time, it is not unusual for can problems to come in waves; a bad batch of cans, undiscovered until they start to leak, will fan out across the country at once, and suddenly many problems occur simultaneously. There's not much Zinsser can do but pray that their suppliers are consistent and reliable, but of course, that is a pipe dream in today's world.

When we were working on the now discontinued Zinsser French Polish, I insisted that it should be packaged in a plastic squeeze bottle, but the DOT said that was a shipping hazard and disallowed it. For those of you who recall, the product came out in an aluminum can, in part to ameliorate this pinhole problem.

Switching the contents to plastic will solve the problem. As for the person who experienced pinholes in plastic, I don't know what caused it but it was not the shellac unless the plastic was one that is not alcohol reistant. Most are. What may be happening there is two entirely different issues that coincidentally occurred in sequence. You should have no problems with SealCoat in the right plastic. When in doubt, use Nalgene or polypropylene.

Finally, do get back to Zinsser with these issues. I will call Susan today and let her know that there is a thread going about this, but the only way Zinsser can know when one of their suppliers, in this case the folks who make the cans, is slipping on the job is with feedback from you.

I hope this helps.

Re: Zinsser SealCoat

#15

Re: I'm here, and here are some answers

Clint Searl, at the base of Haycock Mtn

>Your comments imply that Zinsser expects the end users to do some quality control that they could (should) do in-house.

Clint

Re: Zinsser SealCoat

#16

Re: Zinsser SealCoat

Ron in Weirton

>OUCH!! Don't be picking on can makers as the cause of this problem. I work in the canmaking industry. There are a couple of likely factors causing the problem. One is stirring with steel or very rough and abrasive wood, second (and most likely) is allowing the acidic product to sit for a time after it is opened and exposed to an unlimited air source. The extra oxygen in the head space of an opened can is accelerating the corrosion of the natural product. During manufacturing, the amount of unprotected metal is checked and controlled on a regular basis. We have standards that must be met but even the smallest amount of exposed metal will corrode over time. If you are not going to use the full amount you purchase, you might do yourself a favor and transfer the remainder to the plastic container others have mentioned. As a note not all paints and sealants are acidic which is why you can leave paint in a half used can and not have the same problem. If you reopen a can of water based paint and notice rust around the rim or on the plug, you will see the effect of the metal exposure created when you dug the top off or stirred with a metal rod.

Re: Zinsser SealCoat

#17

Re: Zinsser SealCoat

Ron in Weirton

>OUCH!! Don't be picking on can makers as the cause of this problem. I work in the canmaking industry. There are a couple of likely factors causing the problem. One is stirring with steel or very rough and abrasive wood, second (and most likely) is allowing the acidic product to sit for a time after it is opened and exposed to an unlimited air source. The extra oxygen in the head space of an opened can is accelerating the corrosion of the natural product. During manufacturing, the amount of unprotected metal is checked and controlled on a regular basis. We have standards that must be met but even the smallest amount of exposed metal will corrode over time. If you are not going to use the full amount you purchase, you might do yourself a favor and transfer the remainder to the plastic container others have mentioned. As a note not all paints and sealants are acidic which is why you can leave paint in a half used can and not have the same problem. If you reopen a can of water based paint and notice rust around the rim or on the plug, you will see the effect of the metal exposure created when you dug the top off or stirred with a metal rod.

Re: Zinsser SealCoat

#18

Re: I'm here, and here are some answers

Sawdust Everywhere!

>I just wanted to comment on Michael Dresdner post about transfering unused sealcoat to a plastic container. He said to transfer to propylene or Nalgene containers.

While alot of nalgene containers are propylene or polyethylene, they also make quit a bit of polycarbonate bottles. Polycarbonate Usually clear bottles) is NOT alcohol resistant and will make the plastic brittle. Any form of stress will cause the polycarbonate to crack/fracture and leak.

Re: Zinsser SealCoat

#19

Sorry to go OT with this but

Mike in Savannah

>you just made a light bulb light up in my head. So this is why some of the clear poly. primer bulb(s) in my 2 cycle engines have become brittle and cracked: ethanol additives!

and the answer is?