Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Running air lines in shop

Posts

Running air lines in shop

#1

Running air lines in shop

Terry Alexander

>Fellow woodworkers,

I have a Craftsman 26 gal. air compressor. I am now ready to "pipe" my shop so that I don't have to continously move this beast.

I am installing an in-line filter for moisture and plan on running schedule 40 1/2" PVC. The first question that comes to mind is: What is the best way to attach hose(s) to the PVC?

I guess other than that question, what suggestions do you have for me for this project. FWIW....my shop is 30' x 40' and I have most of my machines along a single wall...which is where I plan to run the PVC.

As always.....thanks in advance.

Terry Alexander

Re: Running air lines in shop

#2

Not PVC

Dan Donaldson

>First thing, it is not a good idea to run pvc. If pvc fails or gets hit, it fails catastrophically and generates dangerous shards. In most areas, it is illegal to use it for air lines.

Re: Running air lines in shop

#3

Should be a "sticky"

Mark Goodall - ATL - tooljunkie

>Like Dan said: "Don't Use PVC for pressurized air lines"

This is one of those questions that pops up here often, and the same responses are repeated. Other forums (non-woodworking) I visit have similar questions that are asked so often that the threads are made "sticky" ..... meaning they appear at the top all the time for convenience.

Happy Woodworking!

Re: Running air lines in shop

#4

I suggest you run type L or K copper pipe

Grant Smith

>Copper pipe is rated for compressed air, and if it leaks, it isn't likely to fail catastrophically like PVC may.

You can get fittings to convert sweat copper fittings to the 1/4" or 3/8" pipe thread you'll want for your compressor fittings.

Do some research on the internet on the subject, and you'll likely find more info about the following tips:

-How to "sweat" copper fittings..it is easier than you might think

-install some slope or pitch to your lines to direct condensate to where it can be drained off and won't collect into the quick release fittings. Install drops so the "T's" point upwards from the main run, then two elbows to turn it back downwards so water doesn't flow into the drop. Install a "drop leg" near the copressor on your line system with a valve to drain off condensate that gathers in the lines.

-use a flexible hose and a ball valve between your compressor and line system so you can isolate the two when you leave the shop...this will prevent minor leaks from bleeding down your air reservoir while you are away. ALWAYS turn off the compressor when you are away...a burst line WILL burn up your compressor if it goes unnoticed.

-For longer runs, consider larger diameter line, such as 3/4". This will keep airlow and available pressure to a maximum. It also increases stored air volume, which means you have more reserve for sprayers, air tools, etc.

-Go to a local industrial tool supplier for your coupler fittings. These will be of higher quality and therefore less likely to leak than homecenter grade fittings. Since there are a few different types of fittings, check with any friends whom you may want to share tools with to find out which types they use so you can interchange.

FWIW,

Grant in Iowa

Re: Running air lines in shop

#5

Re: Running air lines in shop

Kevin French, Antrim, NH

>Like they say "IF YOU GO BLACK (pipe), YOU'LL NEVER (have to) GO BACK."

It's should be less expensive then copper.

It's no sweat

You will need a good size pipe cutter, vise, and a 3/8 pipe threader.

Re: Running air lines in shop

#6

Don't like “sticky”

Rod Peterson -- Ormond Beach

>I also intensely dislike the forum software which is generally associated with that feature. A woodworking forum I was once involved with since its beginning, but have vacated since they became fascist uses that and my big objection was they only had about 20 subjects per page and they almost always head at least four sticky threads. Consequently, fully 20% of page space (every single page) was always taken up with the same message, which if I'd ever read it to begin with, was nevertheless utterly wasted space and a waste of my time.

“Nay, nay,” I say, to sticky threads.

Rod

Re: Running air lines in shop

#7

Re: I suggest you run type L or K copper pipe

Joseph Mulherin, Sr.

>I agree with what Grant has said, however, I would run the piping in galvanized 3/4" because you will not develop rust inside the lines. Make sure that you have the drops installed to catch the inherent moisture that comes with the air.

I am a retired pipefitter/plumber.

Re: Running air lines in shop

#8

Re: Running air lines in shop

Jerry Nicholson

>I heard it said once that the pigment in PCV pipe makes it show up really good on the x-rays.

Jerry

Re: Running air lines in shop

#9

Re: Don't like �sticky�

John K Jordan

>I agree. What might be better than stickies is a searchable KnowledgeBase, similar to this one:

http://www.woodweb.com/KnowledgeBase/KBIndex.html

It is basically a set of compilations of messages. It would supplement the articles and could have be organized by shop hints, finishing, electrical wiring, sharpening, etc.

Of course, it would require someone to volunteer the time to build and maintain it!

JKJ

Re: Running air lines in shop

#10

Re: Running air lines in shop

Pete in Holland, MI

>At the 4000 person manufacturing facilty where I work, sweated copper has been the choice for air for 30 years now.

Benefits:

1) Easy to install if you are comfortable sweating pipes.

2) No rust or corrosion to worry about getting into your air devices.

3) Easy to cut into an existing line and make an addition

4) Requires little equipment to install.

Re: Running air lines in shop

#11

How much line?

Dustmaker Mike

>I ran three lines in my basement shop. I used the rubber hose that came with the compressor for one run and bought another two good quility hoses to run the others. I like the way it can bend a corner and the way I can move it really easy when I rearrange shop tools as I gain one or loose one. It is easy to run in the over head can be repaired really easy and it don't mind being banged with a board or three. But your mileage my and will vary.

Re: Running air lines in shop

#12

Re: How much line?

Geary from NJ

>Can I be so bold to suggest buying a 'roll up" reel of 50-75ft of air hose on a ceiling hung retractable reel? I have one, that can reach any where in the shop,that has been in service for twenty years. It's on my list,for spring,to replace the hose.....so simple.....so easy to put away.

Geary,with a long list trying to make a smaller list w/o spending my inheritance.