Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Hotdog Compressor - Increasing Capacity

Posts

Hotdog Compressor - Increasing Capacity

#1

Hotdog Compressor - Increasing Capacity

Steve in East Tennessee

>I have a Makita hotdog compressor, and it works just great. Would there be any downside to increasing the stored capacity by teeing an auxiliary air tank into the discharge line from the compressor? This is line between the pressure cutoff switch and the regulator manifold.

I'm thinking of putting a tee and a valve in a line to the portable tank, which will more than double the amount of stored air available, while still having the ability to remove the tank for portability. this would allow me to use the Makita for small spray finish applications.

Steve in East Tennessee

Re: Hotdog Compressor - Increasing Capacity

#2

Re: Hotdog Compressor - Increasing Capacity

Mark Mandell - Gone Round In Jersey

>You've got several issues to address, Steve.

First (foremost) is the pressure rating on your aux tank. You must make sure that it is rated the same as your compressor's current tank. Note there are two ratings; burst pressure and working pressure. Remember, as the tank fills and empties, the seams and joints expand and contract. The faster you use the air, the more rapid will be the expansion and contraction cycles. Those portable 5gal air tanks may be fine for taking some air along to fill a tire or run a brad nailer, but they are unlikely to be rated for handling the duty cycling of an active compressor. You will run a real risk of failure and serious injury if you try to cut corners on the tank. Compressed air is, actually stored energy. If that tank fails, it can happen very quickly and with no warning.

Second; you will need a drain port to purge the condensate that will accumulate in the tank in fairly short order. The resulting rust in a wet tank will shorten the life of your unit considerably.

Lastly be aware that your compressor is designed to perform on a given duty cycle. If you double or triple your storage capacity it means that your compressor will have to run 2 or 3 times as long to refill the new volume to the set pressure limit. The longer the pump runs, the more heat it generates and the more wear occurs. Overworking your pump that way will most likely shorten the life of your compressor, so figure that into your "cost-benefit" planning.

Good luck be careful.

mm

Re: Hotdog Compressor - Increasing Capacity

#3

Re: Hotdog Compressor - Increasing Capacity

Pete in Holland, MI

>If your compressor is a dry sump system, you'll run the risk of overheating the seals on the piston and melting them out. If it is an oil sump system, then it'll run longer without damage.

If you are trying to gain more volume so you can use bigger tools than what the compressor is rated for, then you'll only have this extra volume for a short while, they you'll be back to the original problem of not having enough supply for the tool you want to use.

Re: Hotdog Compressor - Increasing Capacity

#4

Re: Hotdog Compressor - Increasing Capacity

Clint Searl, at the base of Haycock Mtn

>Fagiddabaddit.The storage size is irrelevant. It's what's at the end of the line that determines how much the compressor has to run. Either it has the capacity to deliver the continuous volume and pressure required by the tool, or it doesn't. You'll spend more time waiting for the pressure to come up than spraying.

Clint

Re: Hotdog Compressor - Increasing Capacity

#5

Yo, Clint

Mark Mandell - Gone Round In Jersey

>Dat's "Fa-ged-a-bow-dit".

S'mattahwitchoose, don't yous get HBO owdare?

Sheez

|;-}

Re: Hotdog Compressor - Increasing Capacity

#6

Re: Yo, Clint

Clint Searl, at the base of Haycock Mtn

>I left Jersey 16 years ago. Now it's Pennsylvania Dutch.

Clint

Re: Hotdog Compressor - Increasing Capacity

#7

Not Far Enough

Mark Mandell - Gone Round In Jersey

>to loose the accent.

The attitude, maybe, but not the accent

|;-}}}}

Re: Hotdog Compressor - Increasing Capacity

#8

Re: Hotdog Compressor - Increasing Capacity

Larry Clinton At Frankfort (Central)., Indiana

>Steve, what your suggesting would work, IMHO it would cause no problems with your compressor. That said, if you have an Oil-less compressor please understand they have a limited life. They are not designed or built for heavy duty use or even intermittent use in a shop. I say this as I know the testing of the motors (used by the leading manufacturer of these compressors) required a certain number of hours test while loaded with the compressor. These tests "wore out" the compressors and normally required the compressors be replaced to complete the motor tests. Also the amount of air you could "store" at 125 lb. pressure in a small (5 to 30 gallon tank) would not allow you to spray with a standard spray gun for very long - just a few seconds. I base this on the time it takes to drop my 60 gal storage tank from 125 to 90 lb when I use a spray gun. I have a single stage Campbell Hosfield severe duty cast iron stationary compressor with 60 gal storage tank. Mine is barely big enough to cycle when spraying. If I were purchasing now I would look at 2 stage units.

Re: Hotdog Compressor - Increasing Capacity

#9

Re: Hotdog Compressor - Increasing Capacity

Geary from NJ

>This is why they make such good deals on no interest credit cards! Your messin where you oughta not be messin.