Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

garage + wood bug = not enough power

Posts

garage + wood bug = not enough power

#1

garage + wood bug = not enough power

Mitchell

>Hey all,

I built a new garage 2 years ago.

My father in law wired the garage as just that, a garage. I have two ganged 15 amp breakers going to the garage and one 20 amp, 220 line to a single plug that I had used for a construction heater. There is no panel in the garage.

Two years ago when we built the garage, I had no intention of running a wood shop out of it and was just happy to have a garage, but now that I've gotten the wood bug, I can see from reading that I wish I would have had him wire it up as a real shop. Individual circuits for lights, dust collector, heater etc...

The area I have to work is 13' x 18'. 33' x 18' with cars out. The walls are drywalled but not taped.

What is the best solution to add more juice to the garage? I don't think opening the walls and undoing what's been done is a good option, but what about running power to a seperate panel in the garage and using receptacle boxes mounted on the walls (as opposed to inside the walls) for the dedicated lines for a couple more 220 tools, dust collector, Natural gas heater etc...

Any advice is greatly appreciated and no, I wouldn't do the work myself.

Thanks,

Mitchell

Re: garage + wood bug = not enough power

#2

Re: garage + wood bug = not enough power

John K Jordan

>It's pretty easy to cut out sheetrock, add wiring, and patch, especially if you don't care if it looks good enough for the living room. To feed wires, I generally cut out a rectangle between studs or a long strip down the wall long enough to get my drill inside for holes. You can usually patch using the piece you removed - fasten strips of support wood inside across the hole then fasten the piece removed to those strips.

You can do this along the ceiling or floor, then use "existing work" boxes anywhere in the wall. These grip the sheetrock with plastic tabs and are incredibly easy to install. I think this makes a far neater job than externally mounted boxes.

To save money, you might be able to find an electrician who will install the subpanel box and wire the receptacles let you run the wires and patch the walls.

JKJ

Re: garage + wood bug = not enough power

#3

Re: garage + wood bug = not enough power

Barry Irby

>John is right.

Before I got into the woodworking as much as I am now I ran my shop off what you have now. One 220 circuit and two 120 circuits. That works fairly well for a one man shop. But, then I get a DC and An Air cleaner. So, now, Instead of some lights and one tool, I have the DC and Air cleaner running along with the lights and the tool, and then the air compressor kicks on every once in a while.

You need enough amps to run everything you are likely to have on at the same time.

I would allow for my largest tool, the DC, lights, Air cleaner and Air compressor. It is unlikely you will run more than one tool at a time unless you have "help".

I would assume you could get by quite nicely with a 60 amp sub panel. Having said that, you want to use the largest "Can" you can to give you lots of circuits. You may end up with a dozen or more circuits, but remember that they don't add up. It's called the "non concurrent use factor".

Not a bad idea to allow some extra amps, in spite of what I just said. Who knows, you might decide to add a welder to your bag of tricks.

Re: garage + wood bug = not enough power

#4

JL

Re: garage + wood bug = not enough power

JL

>To echo what John and Barry said - there shouldn't be any problems mounting your receptacles on your walls. I did this for my shop on the outer walls (but they were cinderblock, so there was no way that I wanted to cut holes for receptacles in them!).

There is one small "problem" with doing that though. It's nice not having to plan around conduit when you are hanging shelves, cabinets and brackets.

I wired my shop with a 100 amp sub panel. I figured on a 20 amp 220 V circuit for the DC, a 30 amp 220 V circuit for the cabinet saw, a 20 amp 220 V circuit for the bandsaw and numerous 110 V circuits for lighting and the 110 V receptacles.

If you do it yourself, you would save a fair bit of change. I did mine and had an electrician come in to wire my sub panel to the main.

Re: garage + wood bug = not enough power

#5

Re: garage + wood bug = not enough power

Joseph Mulherin, Sr.

>Mitchell, I concur with what John and Barry have said. Back in 1987 when I upgraded my main circuit box to 200 amp, I took the older 100 amp and installed it in the garage/workshop I was also building at that time. I have seven 110 outlets around the shop...all on its own circuit breaker, and a dedicated 220 outlet for the RAS I had at the time.

Yes, if the walls are already covered with drywall use the self mounting boxes John suggested, BUT, before finally installing them, run your wires overhead on the rafters and down a small hole in the upper wall above the outlet you are working on. Fish thru the outlet hole for the wire and pull it thru, run it into the outlet box and then install the oputlet using the fold over tabs to secure. This way you will not have hardly any patching to do.

Re: garage + wood bug = not enough power

#6

A trick

Dan Donaldson

>If you do as suggested (run overhead and down through a small hole in the plate) a trick for getting the wire to the hole for the box is to take a dog choke chain collar, remove the rings and tie it to the end of a small rope. You can drop this through the hole and the weight of the chain will help get the rope down. Also, if there is something in the way, you can bounce the chain around by jerking the rope and many times get it through. We also used to do this where we just had the small hole in both the top and bottom plate. You can usually bounce the chain around and either snag it, or sometimes it will even fall through the other hole. You can then use the rope to pull the wire through.

Of course, this assumes that there is no insulation in the wall you are trying to get through ;-)

Re: garage + wood bug = not enough power

#7

Re: garage + wood bug = not enough power

Mitchell from Canada

>Hey all,

Thanks for the great advice. There is insulation in the walls so it makes things a bit more difficult. I had even considered just unscrewing the drywall in the places I need access to and slicing the vapour barrier to get into the walls. Just using holes big enough for those boxes John described is much less intrusive though.

Good point about having to work around conduit for shelving. It could be a big hassle.

I don't mind doing most of the grunt work myself, it's just getting the power from the panel in the house to the garage that I have no clue about, that and wiring a panel, well that and...heh heh. Running a 100 amp panel sounds great, does my house panel have to have tons of open breaker room to pull that off?

Thanks again.

Mitchell

Re: garage + wood bug = not enough power

#8

JL

Re: garage + wood bug = not enough power

JL

>Does your house panel have to have "tons of open breaker room" - well, sort of. If you have a somewhat modern house (around here at least) - you probably have a 200 amp service. If you have a couple of open slots, you can probably pull your 100 amp sub-panel's power from there.

If your garage is a separate building, you would have to trench down and run the wire from the main to the sub-panel in the garage. If your garage is an attached garage, you would just have to run the wire.

If you aren't comfortable wiring your shop there are a few books available. A couple of books to read are "The Complete Guide to Home Wiring (Black and Decker Complete Guides Series)" or "Wiring" from Better Homes & Gardens.

The price differential between doing most of it yourself and having an electrician do it could be a few $$. But the bottom line is, if you aren't comfortable doing it - don't do it.

My $0.02.

Re: garage + wood bug = not enough power

#9

Re: garage + wood bug = not enough power

Joseph Mulherin, Sr.

>Mitchell, it isn't really hard to run the wires, but making the connections inside your main box should be left to a professional(electrician). Ask around your area for some information on the proper way they want it done(i.e...your building dept. for instance), and they should be willing to show you.

As far as pulling the wires thru the insulation....cut a small hole about 4"sq. at the top of your wall and the outlet hole below, and run a pull tape up thru the insulation...connect the wire to it and pull it back down and connect to the outlet box...then install the box where needed.

Like JL stated use a breaker from your main box and run the new wire out to your shop and install the 100amp box in the wall just like the outlet boxes. Of course a larger hole will be needed above for the many wires to be run down inside wall....or....just mount it on the face and run the wires exposed up to the rafters. Be sure to staple the wires to the rafters securely. You can pick at a book at one of the Borgs explaining about wiring. Good luck.