Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

GM truck question

Posts

GM truck question

#1

GM truck question

jeff

>Hi all

My friend bought a 2001 GM Sierra Truck.

It has 4 wheel drive with 4 wheels on the rear.

My question is this:

Is it possible to remove the 2 outside wheels and use the truck without a problem?

Will it hurt the transmission or Limited slip differential?

I suppose a transmission mechanic would have the answer, but we seem to be short of them here in Vermont.

Jeff

Re: GM truck question

#2

I wouldn't do it but

Dustmaker Mike

>I am not a trany person. It begs the question as to why would ant to do it. For a short run I would do it but to leave it that way No Way. Like I said I am not a Trany person nor a person that knows the real effect of pulling the outside tires but I do know I would not do it for a long run.

Re: GM truck question

#3

Re: GM truck question

M. McNamee

>Your friend will not have transmission problems. He will eventually have wheel bearing abnormal wear issues. The load path from the tires through the wheel bearings is based on wheel offset and center of contact of the tire(s) with the pavement. Removing a tire changes the load path and the bearing will start abnormal wear. In the case of a duelly setup, likely the abnormal wear will be minimal. Now if he loads down the vehicle to the maximum for most of the driving, then the abnormal bearing wear will be accelerated.

Re: GM truck question

#4

Re: GM truck question

Bill Howatt

>I would say the only effect would be the loss of load capability because it has 2 fewer tires to carry the load. This assumes there is no problem securely fastening the single wheels to the hub. Since the outer wheels are the ones removed I'd say the effect on bearing loading would be very little - the outer wheels would put more torquing onto the bearing because of the increased offset.

Why not talk to a mechanic at the GM dealer in your area.

Bill

Re: GM truck question

#5

Local Mechanic has no idea.

jeff

>And he only says that you could run the truck minus a tire for a short time (as in getting in for repair).

But doesn't have the foggiest idea about long term.

This truck was set up to plow and haul trailers and is real heavy duty.

My friend wants to plow with it (and will) but it is very wide and I think he'll crunch the fenders real fast on tight spots.

I thought that narrowing it up would work easier.

Jeff

Re: GM truck question

#6

I wouldn't worry to much......

Basil

>....about the tranny except for over heating since you said he plans to "plow" with it. Single tire will increase traction if he 'doesn't weight it down.....but with a lot of weight added may cause tire failure. Wheel bearings?, I see no problem.

The only real problem I see is the ABS (antilock brake system). It's setup for dual wheels and single wheel use may cause some type of braking problem on the road, like sliding the rear tires when making moderate stops or locking up completely with light use on wet/ice/snow covered pavement.

Re: GM truck question

#7

Plow with it?

Gary Evans Tallassee, TN

>Around here we plow with a tractor! 8^]

Sorry, couldn't resist.

Gary

Re: GM truck question

#8

Re: Local Mechanic has no idea.

George (Oxford, NC)

>All of a sudden you lost me with this last post. How will taking the outside wheel off of each side make the overall width (outside of fender to outside of fender) narrower?

George

Re: GM truck question

#9

Re: I wouldn't worry to much......

Brian in Brighton

>ABS should not be a problem. They work with a little sensor seeing a tooth on the moving wheel flying by it. The teeth are cast into the wheel like a gear. The idea is so simple you'll slap your head when you hear it. The control box keeps a watch on all 4 sensors, when one of them stops sensing the teeth and the others are moving the control box shuts off a valve that sends fluid to that wheel. There is a little back relief on the valve to that pressure in the line is relieved. It will hold the valve shut until it starts to sense the teeth again.

So the only issue with braking would not be the ABS but might be in the brakes themselves. They are designed to stop 2 wheels on a side, not one. So they will have a lot more braking force since the friction on the road is cut in half. I don't know about the master cylinder for a dually, but it might have a different pressure for the rear wheels than the front that will also be messed up.

My 2 cents is to take them off and try it. The worst that happens is that you keep locking up one set of wheels or the other. The tranny and axle should not care. Now if you were to take a single wheel and make it a dually, I would say you could mess up all kinds of things.

Brian in Brighton

Re: GM truck question

#10

Re: Local Mechanic has no idea.

jeff

>He will put on a narrower rear body he has.

Re: GM truck question

#11

I worked in the GM Truck group

M. McNamee

>It does make a difference on the wheel bearing load path. As I mentioned above, if the load is light, no problem. If he loads this down to the maximum all the time, it will make a difference. However, as mentioned, he is going to plow with the vehicle.