Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

PM2000/Accufence issue

Posts

PM2000/Accufence issue

#1

PM2000/Accufence issue

DizD

>Riping some fairly short strips this weekend and noticed a gap between straight edge of the strip and the fence when the strip projected beyond end of UHMW fence side. The gap disappeared when wood cleared end of fence. Checked with a long straightedge and found the two ends of the fence face have kicked out ( away from fence beam).015". The movement in the fence face is from the last attachment bolt to the end. I'm reasonably certain the face was flat when I started out with this saw just over a year ago. I will work on shimming to see if I can bring it back in line. Just wondered if anyone else has noticed this? It appears the unattached ends of the UHMW sides are reacting to stress at attachment points. Will shimming correct this?

Re: PM2000/Accufence issue

#2

Re: PM2000/Accufence issue

James L. Seigal McMinnville, OR

>DIZ, The fence on my NEW PM2000 has the same problem plus high/low areas the length of the fence. I contacted Powermatic about the problem and they sent me new pieces but they have a rough, pebble like surface on them ??? The AccruRip fence on my old Craftsman was much, much better than this piece of junk! Does anyone have a Delta UniFence they would like to trade for a new Powermatic AccuFence with two replacement sides? That, along with other problems with the machine makes me very reluctant to buy WMH Tool Group again.

signed, Very Disapointed

Re: PM2000/Accufence issue

#3

Re: PM2000/Accufence issue

DizD

>I hear you. I was wondering if this was just an issue with the type of plastic. I believe other brands use this same fence material. I started trying to correct it by shimming but haven't gotten it where I want it yet.

I've also had several other small problems from a split in dust hose under the blade shroud to an insert plate which has deformed. So far, everything covered under warranty. I love using the saw and hope to get the "kinks" out eventually.

Re: PM2000/Accufence issue

#4

Re: PM2000/Accufence issue

Dan Mitchell

>James - I got a PM2000 late last year. Haven't had a chance to use it much, been a bit too cold in the shop. I did have to shim the near side of the table a fair amount after checking it with a dial indicator, though I think this falls under expected "tune-up". Can you elaborate on the other problems you've had so I can be on the lookout?

Thanks

Dan

Re: PM2000/Accufence issue

#5

Re: PM2000/Accufence issue

James L. Seigal McMinnville, OR

>Hey Dan, The top has several low spots that run front to back with the lowest spot about .007". That combined with a high spot on the left side of the throat opening of about .008". The rep at Powermatic says that the table is within their specs. When I first reported it, to a different rep., he sent me a new table but it was worse than the original. Also the extension table is warped in the center creating a high spot of .069" where the ext. mates to the cast iron wing. I had a back injury and surgery a few months ago and have not been able to complete the tune-up yet. I thought I was buying my last tablesaw but the General 650 is looking a whole lot better to me now.

Re: PM2000/Accufence issue

#6

Re: PM2000/Accufence issue

Dan Mitchell

>Frank-Quickly checking mine with a straightedge, the top looks pretty good. I know I tend to get a bit obsessed with these things at times, not really sure how much "real world" difference they make. Still, given what we paid, you expect something at least approaching perfection.

Seems like for any given machine, regardless of price, there's someone out there with a warped this or a bent that. I'm looking to add a jointer now, had a 6" Delta a few years back with a warped fence. Actually TWO warped fences, since the replacement they sent was as bad as the original. My experience with the Delta has made me very trepidatous about which one to get (DEFINITELY NOT a DELTA, though as with all brands no doubt many here swear by them). Sometimes I think they just shuffle the bent bits around amongst those who gripe. Reminds me of that old army joke, where the guys who had been out in the field for 2 months are elated when the sarge tells them "Today, everyone gets a change of underwear." That is until he says "Bill, you change with Fred, Fred, you change with Bob, Bob, you change with... " ;-)

Dan