Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

OT Building a custom shower pan

Posts

OT Building a custom shower pan

#1

OT Building a custom shower pan

Steve Silca

>All you home improvement gurus out there: I have a quick question.

I am making a custom shower pan and have done all the research. I know to put the drain in, create a slope toward the drain with portland, install the felt paper, membrane, and then a final thick layer of portland.

Here's my question: All of my research has indicated to put some pea gravel around the drain to allow any water to enter it through "weep holes". I have not found a shower drain at Home Depot or Menards that seems to have these "weep holes". The drain cover just threads into the main drain body. Where do I find a drain that has weep holes ASAP?

Also, any tips/pitfalls to avoid from those of you who have built a shower pan would be much appreciated.

Re: OT Building a custom shower pan

#2

Did this…

Rod Peterson -- Ormond Beach

>First of all, get acquainted with the nice folks at the John Bridge Forum. It's the WoodCentral of tilesetting, and it's loaded with professionals and experienced amateurs who not only can give you a great answer, but can help shepherd you through all the potential pitfalls and anxiety points of the job.

My project turned out not to be as hard as I made it out during the various steps (which you can see at my house remodel page on my website, under Master Bath). I made several visits to John Bridge during my project for propping up and other advice.

The specific answer to your question is that I believe the weep holes are hard to find or are less weep “holes” than very thin slits in or near the threads, but they're there.

One piece of advice I wish I'd taken the time to follow—either shim or notch the studs in the shower area to accommodate the folds of the liner where they go up the walls. Even though the liner is sort of thin (compared to the thicknesses of the tile and studs), two additional layers of it does visibly affect plane of the tiles, and you won't really realize how much until the tile is in and the shower ready for use.

And one thing I did do, and I'm glad, is to let in 2x8s around the inside of the shower area so that if you eventually put grab bars in, you won't have to worry about finding the studs—you'll have plenty of anchor stock to hit. Don't forget to take some pictures and/or otherwise document how high and what width so you can find them later.

Although they sell “moisture resistant” sheetrock at the box, use cement board (Wonder Board, HardiBacker, DuRock, etc.) as your tile backer throughout the shower stall. You will never worry about disintegration or mold later.

Give some thought to putting in a simple seat, if you have room. I didn't (although I had the room), and although I can't say I regret not doing it, every once in a while I ask myself if I shouldn't have. Just something to think about.

Finally, don't worry about the corners of the liner at the ends of the curb. Some manufacturers make a prefab corner you can glue in to avoid leaks at that point (should the pan overflow), but after thinking about it for a while, I realized that the curb represents the high water mark in any event, and preserving the integrity of the liner at that point was minor compared to the exigency resulting from the water being that high in the first place.

Have fun.

Rod

Re: OT Building a custom shower pan

#3

Re: Did this�

Stuart Johnson

>Take your time and be certain each step of the process is exact. I built our shower pan six or seven years ago. At the time I was certain all was good and didn't find out until the first time we used it there is one very slight low spot. Of course with water being so uncooperative it just won't drain from there. It isn't much and will dry by the next morning but I know it is there along with one tile that sticks up just a bit.

Someday I'll redo he floor but anyway you look at it, it is a time consuming pain.

Re: OT Building a custom shower pan

#4

My local borgs had them...

John in New Mexico

>Both the blue and orange stores. As I remember, they were not right in with the rest of the plastic drain fittings, but it varies store by store. Wasn't even a special brand, just an Oatey product. Its a two piece flange, held together with 4 stainless bolts, weep holes are in the top half. Liner gets pinched between these two pieces. Then there is a piece with the drain grate in it that screws into the flange in order to be adjustable for the thickness of your tile. Pea gravel goes in between this piece and the flange. I ended up using an abs fitting instead of pvc, and had to buy a can of that special glue for 1 joint! But its all water down the drain at this point.

We found working with the deck mud a lot easier than expected.

Re: OT Building a custom shower pan

#5

Re: OT Building a custom shower pan

Justin Szeliga

>As was said, John Bridge forums is the best place for tile info. The drain you need is at HD & Lowes, it's made for wet bed shower pans, the plumb dept guys should be able to point you to it. As was said, the "holes" are small, as they aren't supposed to get alot of water in them. I have started using Schluter Systems Kerdi & the drain that goes with that system. Much easier than CPVC sheet, & all it's related fun.

One thing I've done is to put another layer of cement board up to cover the lip from the CPVC liner sheet. The Kerdi makes that sort of problem much less of a hassle.

Have fun!

Peace

Justin