Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Drying cherry

Posts

Drying cherry

#1

Drying cherry

Bill H

>I have a chance to buy some green cherry, but I'm wondering if I can adequately dry it myself. It is just 200 bf so I was thinking I could air dry it on my covered porch. Is this reasonable or will I just turn inexpensive lumber into expensive firewood? I found a chart that said the maximum "safe" drying rate for cherry was 5.8 MC loss/day, with such a high safe rate it would seem I don't need to fear drying too quickly. For the final drying do I need to bring it inside my house or where it will be milled (garage)? I've done some google searching, but thought it best to consult the experts also.

Thanks in advance,

Bill

Re: Drying cherry

#2

Re: Drying cherry

boardman

>Air drying really needs flow-thru type ventilation, so a covered porch would slow it down. Maybe even grow some mold on it if the air is stagnant inside there. The best results will come from having it outside in a breezy location. I've got some walnut drying and on top I laid a cople 4/4's and then a couple sheets of metal roofing to keep the rain off.

Re: Drying cherry

#3

Re: Drying cherry

John Veerkamp

>I successfully dried 800 bf of cherry in an unheated garage. Be sure to sticker it properly with non-staining wood. As was mentioned you need to ensure good air movement. If the poarch is totally enclosed you might need a small fan to move the air. If it is just covered you will be fine. Also be sure to weight it down to prevent warping.

John

Re: Drying cherry

#4

Re: Drying cherry

Gary Evans Tallassee, TN

>Hi Bill,

I'd recheck that chart. I suspect that the 5.8 refers to % of MC loss rather than direct MC points.

Regardless, if your covered porch is open, I would think that it would be a good spot to dry the cherry. You need to keep the sun off it, and I would suspect that you'll need significant weight on top of the stack to keep things from moving around.

There's a publication on the Forest Products Lab website on air-drying lumber. Lots of good info.

Gary

Re: Drying cherry

#5

Lee Grindinger

I agree, check that chart

Lee Grindinger

>I suspect that the moisture loss levels you've noted are for above fiber saturation point, around 28% moisture content and above. Without heat to speed migration of moisture you'd almost assuredly make firewood once free water is gone.

Go to the articles section for an air drying article I wrote for Fine Woodworking then donated to WoodCentral.

Also, How many boards are you talking about here? It can't be many.

Lee

Re: Drying cherry

#6

drying rate

Bill Tindall, E.TN

>There is a large kiln operation near by and they dry poplar right off the saw to 5% and then steam back to 7%, and the whole schedule is less than a week. Cherry doesn't dry much slower. Their schedule for oak is 30 days. The key of course is precise control, something that will not be the case unless the lumber is in a kiln or predryer.

On the other hand, I doubt that it is possible to dry cherry too fast outdoors under ambient conditions in a climate where cherry normally grows. It sure isn't going to dry too fast this time of year.

That said Bill, there are a multitude or ways of ruining a stack of lumber in addition to drying it too fast. For a lot or reasons this is the best time of year to begin drying lumber.

Re: Drying cherry

#7

Re: I agree, check that chart

Bill H

>Lee,

You are probably right on the numbers, it wasn't clear to me from the chart what their units were. You wrote, "Without heat to speed migration of moisture you'd almost assuredly make firewood once free water is gone." Are you saying that if I don't use a kiln, I will ruin the wood? You also asked how many boards, I haven't seen the wood yet, but I would assume ~50 boards for 200 bf. Is this a problem or are you just pointing out that space isn't an issue? Or you don't think it is worth the effort for such a small amount of wood?

Thanks in advance,

Bill

Re: Drying cherry

#8

Lee Grindinger

Turning the heat up

Lee Grindinger

>First of all- No, you don't need a kiln to dry lumber, you can do a perfectly adequate job without anything more than a few stickers and some attention.

I'll try to clear up a few things. The whole science of drying lumber is based upon how quickly moisture at the surface can be replaced with interior moisture as it's removed. As you get further from this moisture migration rate the more likely drying defects occur. Different species have very different migration speeds. Back when I ran two kilns I joked that I could build a fire under pine and poplar to dry them. It was, of course, an exaggeration but it points out how different one species is from another. Some woods like hickory, birch and oak dry much more slowly.

Heat speeds the movement of water through wood. Conventional hardwood kilns are generally run around 185 degrees Fahrenheit to speed the movement of water through the wood tissue. Water in wood takes two forms, free water which is the water between cells, and bound water within the cells. Free water is easy because it does not have to penetrate cell walls to get out and it can be removed at a very fast rate because no wood shrinkage begins until this free water is gone. In fact, free water will literally form a puddle on the floor under a freshly cut board stood on it's end.

It's when this free water is gone, called the fiber saturation point and is around 28% moisture content, that drying becomes more challenging. At this point it becomes important to remove moisture from the surface at about the same rate as the water migrates through the wood tissue. For ambient temperatures such as yours the slower the better. The big boys with their big boy kilns can do what's called conditioning to compensate for issues caused by fast water removal, you cannot and virtually every defect caused by a kiln can be caused by air drying. Like I said, slower is better.

Use dry stickers. Watch for mold. Mold will look blackish or blueish and is not a serious issue unless it persists. Mold cannot flourish above 18% and this is the next critical moisture barrier in drying lumber. If you notice mold on the lumber (think bread mold) change your stickers weekly to avoid sticker stain and increase the air flow slightly but not so much as to cause to much moisture removal and the resulting defects. A bit of mold comes right off in the surfacer so it can be ignored but sticker stain, a problem with cherry, cannot.

Restrain your pile! A couple hundred feet of wood is not much so you'll need to use weight or clamps to restrain the boards as you dry them. I never met the board that would remain perfectly flat by itself during drying but most will succumb to gentle and not so gentle persuasion and remain quite flat after drying Use any means you have to to keep the boards flat during drying or you'll likely end up with potato chips.

Plan on 6 months at least. Take your time and bring your wood into heated areas next fall, this will complete their drying. At this point you can stand them on end or store them in any way that keeps air movement around them.

Okay, enough drivel, I probably raised as many questions as I answered but ask away. I'd urge you to try this, it can be very special to build something out of wood you dried yourself but make sure it's decent wood. If it looks crummy as it's sawn it will look twice as crummy when it's time to look for clear cuts in the workshop.

Lee

Re: Drying cherry

#9

Re: Drying cherry

Sgian Dubh

>One point no-one has mentioned Bill. If you're going to dry from green under a porch try and avoid stacking it too close to a wall. Moisture from the wood, trapped against a wall, can make the wall damp, and even cause mouild to grow. Slainte.