Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Router for Router Table

Posts

Router for Router Table

#1

Router for Router Table

Allen Bryant

>I just recently came into a few bucks and decided to get a router that I can dedicate to my router table rather than taking the one I have in and out. I want something with some horsepower that could drive some of the bigger bits, plus a 1/4 and 1/2 inch collet. I've been looking at the Porter Cable 892 that Amazon is currently selling for 179.99 but reviews seem to be mixed. Anybody use this router and what's your opinion, or does anybody have a better suggestion.

Re: Router for Router Table

#2

JL

Re: Router for Router Table

JL

>I have an PC 890 series router in my router table. I like it reasonably well.

Re: Router for Router Table

#3

Milwaukee

Clint Searl, at the base of Haycock Mtn

>

Re: Router for Router Table

#4

Re: Router for Router Table

George@Colonel's Workshop-Havertown PA

>Good Afternoon Bryan,

I had the less powerful P+C 690 under my table for years, and it did most of the work. I bought a P+C 7518 for large diameter/raised panel bits. Later I invested in a JessEm Mast-R-Lift and am glad I did. Its much easier than lifting heavy machines any more, at least for me, and I can make all adjustments to bit height above the table. While my 7518 may be more powerful than the 890 series, the lighter weight router you propose to acquire should provide years of effective use swinging larger and small diameter bits. I don't see how you can go wrong. I don't use plunge routers under my table, but many others swear by them. Consider plunge routers also.

George

George

Re: Router for Router Table

#5

Yes. For Sure.

George@Colonel's Workshop-Havertown PA

>Good Afternoon Clint,

Also good advice. I bought one for #3 son a couple years ago after he decided against the P+C 890. He really likes it, especially using the strap for control. Lots of power, too. It would be my own choice in that price and power range.

George

Re: Router for Router Table

#6

Re: Router for Router Table

rarebear

>I just got a Millwaukee 3 1/2 hp rebuilt for $180 because of personal discount from www.Heavydutytools.com this was just a few weeks ago so you can try and contact Mike and ask if he can cut you a deal, these have the same factory 5 year warranty,, Has about table adjustment and comes with wrench..

Re: Router for Router Table

#7

Re: EDIT

rarebear

>www.Heavydutytools.net is corret address

Re: Router for Router Table

#8

Triton

Andrew F in Australia

>I find the Triton is an ideal router for a table, Allen.

It was designed with this job in mind, primarily.

Best regards,

Andrew

Re: Router for Router Table

#9

Re: Router for Router Table

David Yoho

>Allen, as you can see, there are any number of choices that would work for you. I was using an older PC-690 in my table but wished for something with a little more HP and variable speed. I didn't feel, for the bits I was spinning, I needed the big PC routers. When the 890 series came out, it was just the ticket for my use because the mounting holes lined up with those I'd already drilled in my table plate, it had the higher HP I needed, and it had variable speed control. The price was not bad either, so I bought one at a show in PA, I think. I also like being able to lock the spindle to remove the bit above the table and I like the above-table height adjustment it offers. The 890 series isn't as slick as some of the other routers you'll find but it works. Mine has been great and the 690 collets are interchangeable with it.

David

Re: Router for Router Table

#10

Re: Triton

Ed Mulligan, Cape Cod

>I'm very happy with my Triton for table or hand-held. No need for a separate (and expensive) raising gadget; the Triton comes with an above-the-table height adjustment handle. Also bit changes are easy with the router in the table.

Ed

Re: Router for Router Table

#11

Re: Router for Router Table *LINK*

knotscott

>The above table features of the Freud FT1700 make it my "go to" favorite. It spends more time in the router table than even my Milwaukee 5625, which is a nice router in it's own rite.


FT1700 review

Re: Router for Router Table

#12

Re: Router for Router Table

Bob Entwisle in NJ

>I've had a Hitachi M12V in my router table for the past couple years.

Amazon was running a special sale and my cost was about 140 bucks. I spent the saved $ on router bits. At the time, the M12V was a lot of bang for the buck. Not sure how their current M12V2 stacks up but might be worth a look.

Re: Router for Router Table

#13

Re: Router for Router Table

The MountainMan

>I agree! The M12V is a great table tool.. It is VS plus slow start...It comes with both router collets - plus I think a third collet - can't remember for what diameter - may be close to the quarter inch - in mm.. And, the price is right - just look around the web - you will find one on sale and shipping paid!! Watch Amazon!

Regards

The MountainMan

by the way - where do you Live in the "Big City".. we are in Buena Vista - supposed to be getting 10-12 inches tonight!! More water for the Ark so all of the rich people can do "white water rafting this summer!!!"

Re: Router for Router Table

#14

Another vote for Triton

Terry in Edmonton

>I started with a Hitachi and later switched to the Triton and am very happy with it.