Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Looking for a router bit

Posts

Looking for a router bit

#1

Looking for a router bit

Ells

>I'm looking for what would probably be called a "double round-over" bit with two different radius-of-curvatures, one about 3/8" and the other maybe 1/8" but exact value not critical, 1/2" shaft. I've searched a lot of web sites but have never found even one with different curvatures. Trying to match some existing kitchen cabinetry.

Thanks in advance for any ideas.

Re: Looking for a router bit

#2

Re: Looking for a router bit

John Ballance

>Can you post a sketch or photo of the profile you are trying to match? Often you can create complex curves by making multiple passes on the router table with different bits. This is a way you can create profiles that don't come stock from a single router bit.

Re: Looking for a router bit

#3

Re: Looking for a router bit

Ed Mulligan, Cape Cod

>If you need just a few feet of the profile, it's usually quick and easy to produce with a series of router bits.

If you need a lot of the stuff, it is worth looking into a custom-made router bit or shaper knives, or have a millwork shop do the work for you.

Ed

Re: Looking for a router bit

#4

Re: Looking for a router bit

Charles M

>I know the radii don't match what you are after but for the sake of clarifying the profile you're after, do you mean double as in a compound curve like this?

Charles M

Freud America, Inc.


img

Re: Looking for a router bit

#5

Re: Looking for a router bit

Mike Fitterling

>Not sure what you are asking, Ellis. Are you looking for a "bead and cove," or "classical," bit where the two round profiles have differing radii? Like this, except this has the same radius on each rounded section. If so, two bits in different passes would probably be the way to go. But maybe I am not understanding what you are looking for.


img

Re: Looking for a router bit

#6

Re: Looking for a router bit

Mike in VA

>Would this work, if you combined two different radius cutters?

http://eagleamerica.com/double-corner-round-assembly/p/157-0245/

Re: Looking for a router bit

#7

Re: Looking for a router bit

Ells

>Thanks for the replies, haven't seen what I'm looking for yet. Tried some multiple passes but doesn't get there. I'll try to post the actual profile this evening. The bit would have two concave sections with straight edges but more radical than what Charles M shows

Thanks

Ells not Ellis

Re: Looking for a router bit

#8

Re: Looking for a router bit *LINK*

Scott Whiting - Glendale, AZ

>Based on your description the Amana 49574 was the closest I could come up with. Hope you do not need a bearing guided bit.


49574 bit

Re: Looking for a router bit

#9

Re: Looking for a router bit - Yes, close

Ells (not Ellis)

>Yes, that's about it, although smaller curve should be even smaller but definitely the right idea. That and another pass to flatten where it comes to a point might do it, needs to be an edge profile not a plunge but would work. For sure closer than anything else I found and negates me needing to figure out how to post a profile, although I had found this as example but where both curves are the same.

http://di1.shopping.com/images/pi/77/d1/13/43341988-140x119-0-0.jpg

Thanks.

Ells

Re: Looking for a router bit

#10

Re: Looking for a router bit *LINK*

John Ballance

>You may want to look at creating the second, smaller radius curve with an ovolo bit if you can't find a single bit to create both portions of the profile. There are many varieties to choose from - Freud link shows one choice. Magnate tools also carries a bit they call a point cutting round over bit - look at www.magnate.net under plunge router bits. The Magnate bit doesn't have the bottom flat that the Freud does.

Good luck.


http://www.freud-tools.com/freudovolobits1.html