Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

ADVICE WANTED; Marble for counter tops

Posts

ADVICE WANTED; Marble for counter tops

#1

ADVICE WANTED; Marble for counter tops

jess bunch

>My Sis is wanting me to install 12"x12" Marble tiles on her kitchen cabinets (counter tops) and I have a question as how best to set them and how to grout/seal the tiles. She wants the tiles layed with "no seams/grout lines", she wants the tiles butted up. Would Buytle calk spread on the edges before butting up work??

Thanks, Jess

Re: ADVICE WANTED; Marble for counter tops

#2

Re: ADVICE WANTED; Marble for counter tops

Pete in Holland, MI

>The tiling I have worked with has a slight corner break on all the corners, so it won't be a smooth transition between tiles even if they are butted up tight. Some sort of grout/sealer will have to be used, else food products will get down between the tiles and start to turn nasty. Check out real granite or marble tiles at a tile source and you'll see what I mean about the corner breaks.

I haven't seen marble used for counter tops either. Seems it is too porus. Granite is the preferred material.

If you go this way, standard tile setting materials will hold it in place.

Good luck !

Re: ADVICE WANTED; Marble for counter tops

#3

Re: ADVICE WANTED; Marble for counter tops

Keith Newton------WebKitFormBoundary4C+dWf+EJaD4HT

>The stone people use some sort of clear caulk around the back splash, not silicone, which I think would be a better choice than buytle.

Re: ADVICE WANTED; Marble for counter tops

#4

Re: ADVICE WANTED; Marble for counter tops *LINK*

Steve Schoene

>I've had kitchen counters with granite tiles. They were installed with thinset and did use unsanded grout on quite narrow grout lines (about 1/16") A key for such tiles is to have a very solid and stable substrate.

I do question the use of marble because of its ease of staining.

The link takes you to a great place on the web to get info about tile and stone applications. The forum has a section specificly for DIY advise, and some very knowledgable pro's do chip in advise in a friendly manner.


John Bridge

Re: ADVICE WANTED; Marble for counter tops

#5

An excellent forum...

John in New Mexico

>I've gotten a lot of good info there, just reading the archives. Fine Homebuilding used to be pretty good too, haven't been to either in a long time.

My only advice is to experiment with your installation in advance. Personally, I wouldn't install marble in a kitchen, and I wouldn't use grout lines less than 1/8", but that's not really what you asked. So I'd say, buy one box of tile, one piece of backer board (Hardibacker is way easier to work with for me), and try tiling a piece of plywood or a little table or something. Also a good idea to test sealers, as I don't think they're much more than films that will protect the tile until they get scratched.

Re: ADVICE WANTED; Marble for counter tops

#6

The WoodCentral of tiling. Great bunch._____

Rod Peterson -- Ormond Beach

>

Re: ADVICE WANTED; Marble for counter tops

#7

White modified thinset; 1/16" grout lines;non sand

Clint Searl, at the base of Haycock Mtn

>If you're going to face the counter edge, PL brand polyurethane construction adhesive is a great stickum.

Clint

Re: ADVICE WANTED; Marble for counter tops

#8

Re: ADVICE WANTED; Marble for counter tops

Mark Mandell - Gone Round In Jersey

>I've done several kitchen tables with marble tile. I used MDF for the substrate, and glued the tile down with vinyl tile adhesive. You will need several longer straight edges (at least 3') to get your tiles set level to each other in both directions.

Joints were set at 1/16th (corner shims make life easy) and, instead of grout that will stain and/or crack and have to be renewed, I used 30-minute epoxy tinted to match the stone as filler. Tables have done well.

For the epoxy, let the adhesive (or thin-set) dry for 2-3 days after you carefully remove any squeeze in the joints. Then start by paste-waxing the top surface of the tile. Fill the joints with epoxy using a thin blade to work out any air. Then, when the filler gets to the "leather hard" stage, slice off the excess epoxy with a razor blade, followed by a wipe with alcohol. Stay away from acetone and similar solvents as they will attack and ruin the factory polish on the stone. Wait several days for a good solid cure, wipe down with alcohol to remove the wax, and apply stone sealer/polish.

What edge treatment are you going to use? I use a chamfered wood strip that matches the rest of the piece. If, however, you're going with a marble edge, you're going to have to do some polishing.

mm

Re: ADVICE WANTED; Marble for counter tops

#9

PS

Mark Mandell - Gone Round In Jersey

>Stone gets HEAVY in a hurry. Make sure that your top is well supported to prevent sag.

Re: ADVICE WANTED; Marble for counter tops

#10

Re: PS

Jess bunch

>Thanks for all the input, I will certainly apply your helpful ideas and sharing your experiences.

Yes I am going to face it [ stained oak ]. The cabinets themselves are dark walnut stained oak raised panel. Cabinets were built in/on the job by local cabinet builder/

Jess

Re: ADVICE WANTED; Marble for counter tops

#11

Re: Facing

Mark Mandell - Gone Round In Jersey

>What I did was to mount the facing with "0" biscuits making sure that the edge was about 1/32" below the top of the tile. Then I carefully cleaned and waxed the router's base plate and chamfered the edge to leave a 1/16th of wood at the top edge, then sand (stain) and finish. Makes a nice edge that also protects the marble from chips.

mm