Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Stain Questions

Posts

Stain Questions

#1

Stain Questions

Rick Jackson,TN

>Youngest son sent a plan of an entertainment cabinet, the plasma screen will sit on top and the components behind frosted glass doors, nickel legs/feet and hardware, etc. What D-I-L wants is "black" wood. I believe she wants to see the grain of the wood so that rules out laminate, and I'm sure she wants a deep black. So:

What wood is suggested for the cabinet? Maple?

What stain to use? Store bought or a mix?

Appreciate the help, Rick

Re: Stain Questions

#2

Re: Stain Questions

Clint Searl, at the base of Haycock Mtn

>Oak: Ronan brand lamp black pigment paste reduced with naptha; clear lacquer.

Clint

Re: Stain Questions

#3

Re: Stain Questions

Steve Schoene

>If she has the "Pottery Barn" deep brown, not quite black (expresso) finish in mind then thare are done on a diffuse porous wood such as maple or poplar. One way is to start with an aniline dye to get the basic darkness and limit "blotching" to a degree. Then after sealing a gel stain can be used as a glaze or toner to even the color and add some depth.

I'd be sure to make some finish samples for her to sign off on before starting the project. May make your son's life easier.

Re: Stain Questions

#4

Lee Grindinger

I always liked ash for this look

Lee Grindinger

>Ash has a great texture for the look in which you see the grain clearly but the wood is basically black. Aniline dye works well for this.

Lee

Re: Stain Questions

#5

agreed

Bill Tindall, E.TN

>Milk paint or its equivalents work nicely on it too for all the reasons you describe.

Maple is going to look like black plastic to my eye.

Re: Stain Questions

#6

very dark finish method

GolfSteve in Calgary

>My woodworking club recently visited a professional finishing supply company. They do tons and tons of work locally and gave us some good demos.

They swear this finishing schedule doesn't cause any problems, and it certainly resulted in a very dark finish on hard maple with about one minute of work for a cabinet door. Maple is usually very hard to get a dark finish on, and getting an ebonized finish that quickly was impressive.

1. Sand to no more than 180-220 (he stressed that roughness was key to getting good bite with stains).

2. Wipe on a dark water based wiping stain. Wipe off well.

3. After a minute or two, apply a dark oil based wiping stain.

The net result was an intensely dark, evenly applied stain on hard maple using only one coat of dark water based followed by one coat of dark oil based wiping stain. After letting dry for ~30 minutes, they top coated with water based lacquer.

In my mind, I wonder if the use of water based wiping stain couldn't be replaced with a quick wipe with a wet rag - the effect being to raise the grain creating more roughness for the oil based stain to bite into, but I didn't ask that question during the demo. I'm sure these guys have experimented enough that the choice of water based stain followed by oil based stain is optimal :-)

The combinations of oil/water products and short drying times go against most of what I've read, but they are pros and do this all the time without failure.....YMMV

They said their biggest challenge was applying the water based stain fast enough to keep a wet edge. They ended up modifying an airless sprayer to apply stain at a huge rate so they could keep an entire conference table wet.

Re: Stain Questions

#7

Re: agreed

Steve Schoene

>The maple doesn't have to look like plastic if the dye/stain isn't fully opaque.

I do like the black ash look as well, though it is a lot different than the Pottery Barn/Restoration Hardware look that is so popular. I assumed the latter, but you may well be right that the original poster has the former look in mind.

Re: Stain Questions

#8

Re: very dark finish method

Rick Jackson,TN

>Thanks for all of the great input and ideas guys. I'll let you know how it works out and what method I used. As always, I will post a photo. Rick