Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Jessen Mast R Lift Problem

Posts

Jessen Mast R Lift Problem

#1

Jessen Mast R Lift Problem

George@Colonel's Workshop-Havertown PA

>Good Afternoon Friends,

Has anyone had a problem with the Jessen Mast-R-Lift insert rings? I've been using the lift for a little less than a month, and the insert ring which had come with the lift has been used to satisfy most of my current router needs. However, I had to swap out and install another ring to accommodate a larger diameter bit, and found out the insert ring is frozen in place. Jessen supplies a wrench which incorporates two pins which are accepted into corresponding holes in the insert rings. I tried tapping the wrench with a wood block and dead blow hammer to loosen the ring, but the ring wouldn't budge. I squirted some penetrating oil into the ring circumference without success. I verified I was tapping in the correct direction to loosen the ring, and then one of the prongs broke out of the plastic wrench, and took off for outer space. The prong is roughly the size of a pencil eraser, and I can't find it in the shop. This renders the wrench useless. The insert is still frozen, and the Jessem Technical person was unavailable to address the problem when I called. Hopefully, they will call me back. Anybody have any comments or ideas?

George

Re: Jessen Mast R Lift Problem

#2

Re: Jessen Mast R Lift Problem

Wayne Carson "TX"

>I have the same problem but haven't broken anything yet. I have learned not to tighten them very much. If you find out anything from them I would like to know. I think that saw dust gets in the groove and causes them to bind up.

Re: Jessen Mast R Lift Problem

#3

Re: Jessen Mast R Lift Problem

Garrett in Victoria

>Hi George

To loosen the insert ring you must turn it clockwise as you look down on it. (That's the opposite of what one would expect.)

You can easily make a new wrench from a piece of half-inch baltic birch and some dowelling.

Finally, it's a friction fit, and I suspect you've cranked it rather tight. I've learned that the best way to free something like this up - after you make your replacement wrench - is to start tapping the handle of the wrench quickly and lightly, continuing for however long it takes for it to break free. Patience really is a virtue here.

Cheers, Garrett

Re: Jessen Mast R Lift Problem

#4

Re: Jessen Mast R Lift Problem

Kneale Brownson enjoying snow in N. MI

>An adjustable pin wrench should help too:


img

Re: Jessen Mast R Lift Problem

#5

FIXED and THANKS

George@Colonel's Workshop-Havertown PA

>Good Afternoon Friends,

I did not receive much actual help from JessEm, but they are sending me a new 1 1/2" insert and new wrench. I found the missing prong and tapped it back into the wrench. I noted part of the problem lay with the prongs jumping out of the holes in the insert as the wrench was being tapped/wacked to force rotation. This occurred even when I was tapping lightly. I engaged the wrench in the insert and sandwiched the insert and wrench between two wood discs, about 1/2" thick. I ran a1/4" machine bolt with fender washers, lock washer, and hex nut thru the center of the insert and wood discs. Tightening up on the nut, I was able to trap the wrench tight against the frozen insert, and that kept the prongs engaged. I needed a 16 oz claw hammer and a short length of wood and fast moderate taps before I could get the insert rotation started. Once begun, the plate rotated out pretty quickly. Examination of the edge of the insert and aluminum router plate did not show any significant amount of dust/dirt. So it wasn't clogged. In furure use, I will insure any insert used is rotated only enough for it to engage the locking profiles, and no more. Tolerances may be too tight and the materials used may not be slippery enough to permit easy rotation. JessEm stated they had not had any complaints of one of their inserts having been frozen in place as tightly as mine. I find that hard to believe. I do credit them for sending me a replacement insert and extra wrenches.

George

Re: Jessen Mast R Lift Problem

#6

Re: FIXED and THANKS

Mark Katz (Boston)

>Have the same problem on my Jointech Router Lift Pro which is made for Jointech by Jessem and is a variation of the Mast-R-Lift. Mine is several years old. When I approached a Jessem rep at a WW show about it, he disclaimed any knowledge that the Jointech unit was made by them and would not offer any help.

Re: Jessen Mast R Lift Problem

#7

Hey Mark,

George@Colonel's Workshop-Havertown PA

>Good Afternoon Mark,

Are you still experiencing the problem, or were you able to free the frozen insert? Yeah, I know what you are saying: I was a bit miffed by those people too, disclaiming any knowledge of a similar problem as severe as mine. I have to admit that the damn thing works like a charm and I really like the device, expensive as it is.

George

Re: Jessen Mast R Lift Problem

#8

Re: Hey Mark,

Mark Katz (Boston)

>I do still have the problem, George, but I also do not tighten them very far any more.

I really like Kneale's idea of the adjustable pin wrench. I did a google search and it looks like the Facom 117.B might be the right match (but pricey). It would give a lot more leverage than the little short-handled thingy supplied with the lift and the pins wouldn't break either.

I had thought about ordering a new set of inserts directly from Jessem because I thought maybe Jointech made their own, inferior substitute. But since yours are Jessem inserts on a Jessem-branded lift, it looks like that might not help much.

Hope the new set they send you works better than the old ones. Let us know.

Mark