Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Tiger Maple Blanket Chest (PICS)

Posts

Tiger Maple Blanket Chest (PICS)

#1

Tiger Maple Blanket Chest (PICS)

David Yoho

>This is the tiger maple blanket chest I recently completed. During its construction I tried many new techniques and will continue using most of them going forward. This chest features a beautiful antique look from the rustic black iron hinges to the multi-colored dyed finish and the ogee bracket feet. The main wood is curly (tiger) maple and I also used poplar for the web frames, aromatic cedar for the chest's bottom, hard maple for the back panel of the chest, and quarter-sawn sycamore for the drawer boxes. All of the hardware is from Horton Brasses.







This shot shows off some of the nice figure with the lid up. I applied eight coats of Waterlox Original Sealer/Finish (medium sheen). The chest consists of two cases, which join where the waist molding is located. I cut the through dovetails using my new Leigh Super jig. I actuall used more hand tools on this project than ever before. Those I put to work included several planes, a spokeshave, cabinet scraper, coping saw, chisels, rasps, and rifflers.







The inside of the chest features a tongue and groove aromatic cedar bottom that simply rests on top of the upper web frame. It is held in place with a curly maple quarter round molding that I attached to the chest with some 23-gauge pins. The molding is back-mitered for a snug fit and the look of a true mitered joint. The reason I installed the bottom this way is if someone has the chest locked and has lost both keys, it's a simple matter to come from underneath, pop the bottom out, and remove the screws holding the lock. This would be an easier repair down the road than the alternative! The cedar can also move independent from the case, which is always a good thing.

One thing I did new on this project was to finish the inside of the two cases before joining them together. Once the entire thing was assembled (minus hardware), I applied additional coats of Waterlox to complete it.







The drawer boxes are 1/2" quarter-sawn sycamore and I hope you can see some of the figure in this shot. The bottoms are 1/4" thick with the grain running horizontal front to back. The bottom floats in the grooves but is held with a single #4 screw centered in the back rail. The bottom is slotted in the center for the screw so it can move. I dovetailed the drawer box front and back. The front of the drawer box is a piece of 1/2" tiger maple. The false drawer fronts are 1/4" tiger maple that I glued and clamped to the piece on the front of each box. The end result looks like a rabbetted dovetail joint in 3/4" stock but without the hassles of really doing it.







Thanks for looking,

David

Re: Tiger Maple Blanket Chest (PICS)

#2

Lovely!

Mike Schwing from Md.

>

Re: Tiger Maple Blanket Chest (PICS)

#3

Wow! Beautiful!

Tony - Memphis

>Nice work! Great wood and craftsmanship.

Tony

Re: Tiger Maple Blanket Chest (PICS)

#4

Re: Tiger Maple Blanket Chest (PICS)

Robert R Clough - Thorncraft

>Yes, beautiful! Excellent - I like your interior work.

Re: Tiger Maple Blanket Chest (PICS)

#5

Re: Tiger Maple Blanket Chest (PICS)

Thomas Skaggs, Foothills of Mount Level

>David,

Truly an heirloom piece there. Looks like you got a hold of some very nive wide maple. The colorization really pops that figure.

Beautifully done and well crafted. Great job!!

Tom

Re: Tiger Maple Blanket Chest (PICS)

#6

Very nice

Keith Newton

>Isn't it great to get some great looking wood like that, even though it can be a bit tricky to work, then turn it into a great finished piece.

I believe I saw a bigger pile of that lumber in a photo when you went after it. What are you planning to do with the leftovers, send them to me? ;-)

Re: Tiger Maple Blanket Chest (PICS)

#7

Sweet ...

Joe Burke

>That's a nice warm brown ...

Re: Tiger Maple Blanket Chest (PICS)

#8

A real beauty!

John McGaw

>Looking at that makes me want to get back to the shop.

Re: Tiger Maple Blanket Chest (PICS)

#9

Alan Young

David,That is a stunning piece of work. ..A ?

Alan Young

>The lid appears to be solid pieces edge glued together with a molding wrapped around the perimeter. How is the molding on the lid attached? There must be some wood movement issues that you tackled here.

A really fine combination of style,wood and finish...

Alan

Re: Tiger Maple Blanket Chest (PICS)

#10

Pleas include in Shop Shots

Mike Farinella

>Absolutely beautiful David.

Re: Tiger Maple Blanket Chest (PICS)

#11

Re: Tiger Maple Blanket Chest (PICS)

HC Sakman

>Wow...! Very nicely done David! Finish looks superb, though so does your craftsmanship.

Excellent piece!

Chico...

Re: Tiger Maple Blanket Chest (PICS)

#12

JL

Re: Very Nice!!!!

JL

>

Re: Tiger Maple Blanket Chest (PICS)

#13

Outstanding!

Clint Searl, at the base of Haycock Mtn

>

Re: Tiger Maple Blanket Chest (PICS)

#14

Re: Tiger Maple Blanket Chest (PICS)

GolfSteve in Calgary

>Very nice, David. Put a few tills in there and it can do double duty as a toolbox in the shop :-)

No secret compartments, or are they a secret?

Re: Tiger Maple Blanket Chest (PICS)

#15

Can't Get Any Better Than That

George@Colonel's Workshop-Havertown PA

>Good Afternoon David,

Everything about it is grand. Superb choices of materials. Craftsmanship and finish are of the first order. That s the prettiest blanket chest I've ever seen, and that's a blanket statement.

:<)

George

Re: Tiger Maple Blanket Chest (PICS)

#17

Re: Tiger Maple Blanket Chest (PICS)

David Yoho

>Thanks, Tom.

The board for the upper case was about 13 inches wide. However, since my jointer is only 8 inches, I had to rip it and reassemble it later.

One interesting technique I employed on this chest is how I cut the boards so they wrap around the front and ends on the upper and lower cases. From the back edge of one end to the back edge of the other, the boards were cut so the grain followed all the way around. Because of their length, I had to use other boards for the back.

The board for the lower case front, where the drawer openings are, was cut into five pieces and reassembled to create the openings but allow the grain to flow.

David

Re: Tiger Maple Blanket Chest (PICS)

#18

Re: Very nice

David Yoho

>Keith,

After seeing that spectacular wood in your recent Shop Shot submission (coming soon), I'd say this stuff is too tame for you!

Actually, I thought I bought enough to make two chests but it looks like I missed it by a little. I need to buy some more to add to what is left so I can get started on another that has been ordered already.

David

Re: Tiger Maple Blanket Chest (PICS)

#19

Re: David,That is a stunning piece of work. ..A ?

David Yoho

>Thank you, Alan.

Yes, the top consists of three pieces glued into a panel with the molding attached around the front and ends. The way I did it was to first cut and miter the three pieces to fit. Next I glued the mitered corners and let them set up. Then I positioned the molding on the front, glued, and clamped it. I applied glue to the first inch at the front of each end also.

Once this set up, I went about attaching the two end pieces. I positioned each one using clamps, drilled pilot holes, and used four equally spaced 4-penny finish nails to hold it. To hide the countersunk heads, I set them with a standard nail set and finished driving them in using a #2 square head bit (like you use to drive in square head screws). This left square holes which I filled with 1/8" by 1/8" plugs I cut on the tablesaw. A little glue, tap them in, cut them flush, sand, and they become almost invisible in the end.

After finishing the chest, I realized the top had already moved just a little because I could feel the ends of the molding were just a little proud of the rear edge and they were flush when I installed them. I guess this means it's working!!

David

Re: Tiger Maple Blanket Chest (PICS)

#20

Re: Tiger Maple Blanket Chest (PICS)

David Yoho

>If I told, they wouldn't be a secret!

Thanks,

David

Re: Tiger Maple Blanket Chest (PICS)

#21

Re: Can't Get Any Better Than That

David Yoho

>Evening, George. I'd say you about covered it!

Thanks,

David

Re: Tiger Maple Blanket Chest (PICS)

#22

Thank You Everyone

David Yoho

>Thanks for all the kind words. I really enjoyed building this project and have plans to build several more. The color in the photos doesn't quite come through like it looks in person. It looks pretty close to some cherry furniture we have in our dining room with a hint of red showing through the amber color.

I plan to do a Shop Shot on this project as soon as time allows. My focus will be to share some of the construction tips I followed in making this beautiful piece.

Again, thanks. It sure was a lot of fun to work with such exciting wood!

David

Re: Tiger Maple Blanket Chest (PICS)

#23

Re: Can't Get Any Better Than That

Matt Robinette,Mt Juliet Tn

>That is just plain outstanding. I was wondering about the feet and how you built them. Did you use 8/4 stock? Thanks again for posting it.

Matt

Re: Tiger Maple Blanket Chest (PICS)

#24

Feet

David Yoho

>Yes, I used 8/4 stock for the feet. I think they were probably the easiest part of this project. I cut the two pairs of front corner feet oriented so the grain would continue from foot to foot once mitered.

David

Re: Tiger Maple Blanket Chest (PICS)

#25

Re: Tiger Maple Blanket Chest (PICS)

Thomas Skaggs, Foothills of Mount Level

>Good Call David. That continuity is what elevates the craftsmanship. Very well thought out!

Tom