Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Cutting you own stringing? Ideas please

Posts

Cutting you own stringing? Ideas please

#1

Cutting you own stringing? Ideas please

Henry (Raleigh NC)

>I have recently been dabbling with adding stringing to my projects and I�d like to hear how others do this. A recent Popular Woodworking article has some details on processes to use for creating the groove to lie stringing in, as well as some ideas for actually making the strips/stringing. I am looking for more help.

I am using a very small (1/16", maybe 3/32"?) router bit and a router table to create the shallow groove for the stringing. That has worked reasonably well.

I have more difficulty with cutting my own stringing. The PWW article suggested the possibility of using a marking gauge to cut narrow strips from veneer. That is a usable approach, certainly for small pieces. The setup is short and it is quick. Splits along the grain have been a factor using this approach.

I am resawing scrap lacewood pieces with my TS or BS to create narrow veneer-like pieces. Then I am attempting to cut the stringing from those veneer-like pieces. Typically for me these pieces are only an inch or so wide, so it seems inappropriate to label this as veneer � they are thin strips.

Dimensional control for the actual stringing is only critical in one dimension; the stringing needs to be the same width as the groove I have cut. The other dimension just needs to be larger than the depth of the groove, and any additional material will be sanded off. That one critical dimension is where I am having issues � I need more precision in at least one of my cuts so that I can achieve that constant thickness or width of the stringing. T

I am now trying to make picture frame stock that incorporates stringing. Here I am trying to do 6' pieces - not necessarily with long continuous pieces of stringing, but using many 6" pieces gets old. So here I am trying to use longer stringing pieces, at least 12-18". For this I have also tried a second approach suggested in the PWW article � using a zero clearance secondary table on the bandsaw and cutting the stringing from the veneer strips. That has proven faster, and reasonably accurate, but not accurate enough I think. Cutting the stringing on the TS has not worked well; the resulting stringing does not have enough rigidity to avoid flutter near the back of the blade and the rising teeth take some or all of the piece. It just does not survive the TS journey with a consistent dimension.

One change that I expect would make a difference would be a much finer tooth BS blade. As I am thinking about it, I would guess that sandwiching these thin strips between thin plywood might also be a way to keep it stable; that seems like a tip I have seen for cutting thin metal sheets.

Anyone else cut their own stringing? How do you accomplish this?

Thanks for your ideas.

Henry

Re: Cutting you own stringing? Ideas please

#2

Re: Ideas *LINK*

Mark Mandell - Gone Round In Jersey

>Henry,

Do a net serach for "compwood". This is a flexible processed wood material that you may find very suited to what you're doing. The link is one example

Since you identify only thickness in one direction to be the critical factor in your shop-made material, I'd try to get close with the BS and then set up a planing operation either with abrasives (sanding block) or blade (plane/scraper) between a pair of shooting rails. With either of such, you should be easily able to get a consistent thickness to a .001th or less.


compwood

Re: Cutting you own stringing? Ideas please

#3

Re: Cutting you own stringing? Ideas please

tek-Brunswick, Ohio

>Mark, has a good idea in using a shooting board. If the wood is thin enough to be fragile then it must be sandwiched between the shooting board and a piece of wood on top of the veneer.

If it is thin enough to cut with a veneer saw it can be cut with the veneer saw and a straight edge. If you haven't used a veneer saw before. A new one needs to be sharpened before use. Hone the bevel on either side of the blade until the edge is sharp. If the ends of the teeth are now flat they need to be filed back to a points. File straight across like a rip saw. On a fine stone, take one or two swipes on the side bevels to get rid of the burr. The edge of the saw should be like a row of knife points. Take a board and put two gage blocks on the ends of one edge. The blocks should be thickness you want the stringing. Butt the veneer against the edge of the board, the blocks should overlap the veneer. Butt a straight edge up against the blocks. Push down on the straight edge and remove the guage board. Run the veneer saw or a sharp knife against the straight edge. It will take several passes to cut the veneer. Make the first cut very light. This makes a track for the other passes to follow.

Re: Cutting you own stringing? Ideas please

#4

Re: Cutting you own stringing? Ideas please

Robin Corell in Atascadero, CA

>A marking guage really does work well for cutting. You may need to make a few modifications though. The blade needs to be sharper for cutting than it does for marking. The blade needs to be thinner; this kind of depends on your existing marking guage. Some marking guages have a very obtuse angle and this will act like a wedge rather than a blade when cutting. I prefer a panel guage with a wheel blade for marking and for cutting this seems to work well.

When cutting the first pass should be a light scoring cut with gradually more pressure on the successive passes with the cutter. Different woods will require different numbers of passes to make the cut.

Robin

Re: Cutting you own stringing? Ideas please

#5

Re: Cutting you own stringing? Ideas please *LINK*

Kris Lasure

>Check out the link for inlay tools at Lie-Nielsen. They have have a thicknessing gauge for stringing.

I've also seen these gauges homemade and work well. Not much to them.


Inlay tools

Re: Cutting you own stringing? Ideas please

#6

Re: Cutting you own stringing? Ideas please

Tony - Memphis

>There was a real good article by Steve Latta in FWW last month I think it was on the subject. He has developed a real easy and dependable technique. He has done a couple of visits to the Woodright's shop showing how to do stringing too (you might can find the videos). I'm pretty sure FWW has an online video of Steve showing his technique. Lie-Nielsen just started making a version of his tools and they sell a DVD as well. The tools are not hard to make, but the DVD would be a good reference. I think there is a drawing of his slicer on FWW too.

Tony

Re: Cutting you own stringing? Ideas please

#7

Re: Cutting you own stringing? Ideas please

Barry Irby

>Wonder if a paper slicer would work?

I would try a paper cutter and if that did not work, I would make a couple of slightly curved cauls and have a bolt in each end to pull them tight together. Put the pieces of thin wood between then and allow enough projection to make the width of the stringing. Then I would use a marking knife or other knife that was flat on one side to cut the string off the side of the caul. The drive in the cauls or causal would be so that it would apply firm pressure over its length. It could be as long as you need. I would use a marking knife to avoid slicing into the face of the caul. You could make it one caul and a piece of melamine or a piece with Formica on it to slice against. If you use two cauls, you could slice from both sides.

if the knife did not work you try a saw like one used to open stuck windows, a window zipper.

Another approach would be to stack up a number of pieces between the cauls and slice all of them on the bandsaw.

My understanding is that the stringing is supposed to be slightly too wide. You tamp it into place and then use a card scraper to level it.

Re: Cutting you own stringing? Ideas please

#8

Re: Cutting you own stringing? Ideas please

Thomas S Stockton

>I make 1/16 inlay or stringing by sending a board I've resawn through my thickness sander and then ripping the piece on a bandsaw. I cut the groove with a router although if I were going to go any thinner I would probably use the more traditional techniques and form the groove using hand tools. The pictures below show 1/16" inlay along with mother of pearl. If your trying to do a reproduction I think that 1/16" is getting a little wide and heavy for stringing especially on table legs. Steven Latta did a real nice article in a very recent Finewoodworking on stringing that you might like to check out.

First pic is of the inlay strips

Tom


img

Re: Cutting you own stringing? Ideas please

#9

Re: Cutting you own stringing? Ideas please

Thomas S Stockton

>The grooves I cut with a router are deep enough to hold the inlay in with out clamping, so if I made the inlay the right thickness I can lightly tap it in with a block of wood and a hammer.

Here is a piece ready to be inlayed. it is then planed and scraped flush. You can see in the lower left were I hit it a little to hard and crushed the inlay, luckily it is all above the surface and cleaned up nicely

Tom


img

Re: Cutting you own stringing? Ideas please

#10

Re: Cutting you own stringing? Ideas please

Thomas S Stockton

>Her are what some table tops look like with the ebony and mother of pearl inlay ready to be sanded. sorry about the image quality

Tom


img

Re: Cutting you own stringing? Ideas please

#11

Re: Cutting you own stringing? Ideas please

Thomas S Stockton

>here is a detail shot of the drawer front and leg

Tom


img

Re: Cutting you own stringing? Ideas please

#12

Stringing thickness gauge?

Henry (Raleigh NC)

>Kris - Thanks for the link. I would not have thought there would be tools out there for this. How does that thickness gauge work? I can't quite picture that. I have not seen the DVD from Lie Nelson, or the FWW videos.

Henry

Re: Cutting you own stringing? Ideas please

#13

Thank you - Cutting your own stringing?

Henry (Raleigh NC)

>Thanks to all for your ideas. I have not watched any DVDs on this, although it seems that there are some out there. I will check these out, as well as the FWW article.

Henry