Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Adjusting to Square

Posts

Adjusting to Square

#1

Adjusting to Square

George@Colonel's Workshop-Havertown PA

>Good Afternoon Friends,

My best friend Charlie and I are building a Grandmother Clock in my shop. Since it will be his clock, Charlie (in left of picture)selected air dried cherry which we bought from a newly discovered local band mill operation. We resawed 5/4 strong lumber to 3/4" S4S and saved the fall off for veneer. The veneer will become the back of the base, waist, bonnet, dial face and bonnet top.

We used great care adjusting the table saw blade to exactly 45 degrees to bevel the edges of the front and side facings. The #0 biscuit slots were precisely positioned. We used Titebond II to join the front and sides, and the back is pinned within the side rabbets temporarily. The picture shows us easing the assemble into precise alignment. Quality workmanship is hard to beat! :<)

George


img

Re: Adjusting to Square

#2

Alan Young

Col. You should be reprimanded

Alan Young

>for not wearing your WC hat while on active duty.

tisk! tisk!

Alan

Re: Adjusting to Square

#3

Re: Adjusting to Square

John_in_Az

>I can see why you say "easing" it into position. Those hammers are totally inadequate for that job. The proper equipment would have be a 20 ton hydraulic press, properly shimmed of course. BTW, nice start on the clock. John

Re: Adjusting to Square

#4

Re: Adjusting to Square

Ken Oakley-Sunny St. Cloud, Fla

>I didn't think anyone smoked a pipe anymore. I did for 35 years and am now paying the price for it. I sometimes think it was more a pacifier than a smoking instrument.

Re: Adjusting to Square

#5

Glad To See

Mark Mandell - Gone Round In Jersey

>You're both wearing your safety glasses. Too many youngsters today forget them when doing BTS adjustments.

Re: Adjusting to Square

#6

I see FAT!

Grant Smith

>That's F.A.T.

I common military acronym which stands for "Fine Alignment Tool"

We generally chose larger FATS, but the FATS in the photo look like they'll serve the need just fine.

Regards,

Grant in Iowa

Re: Adjusting to Square

#7

Unless you're Stacy David…

Rod Peterson -- Ormond Beach

>> That's F.A.T.

> A common military acronym which stands for "Fine Alignment Tool"

Stacy uses a “B-F-H” which looks to be about a 40oz. Big Hammer.

Rod

Re: Adjusting to Square

#8

JL

Re: Or are you distressing the wood???

JL

>I thought you were supposed to use chains and keys :).

Re: Adjusting to Square

#9

As they say on Mythbusters.....

Thomas Skaggs, Foothills of Mount Level

>....if it's worth doing, it's worth over-doing! ;-)

Tom

Re: Adjusting to Square

#10

What exactly is in those pipes?!?

Dan Mitchell

>

Re: Adjusting to Square

#11

Do you remember

Ken Garlock, Collin County Texas

>an item used in electronics called a Glo-bar resistor? I was once told by a mainframe computer repairmen that the bar in glo-bar stood for Big A** Resistor, B.A.R. This discussion led to all sorts of other large things. A truck tire could be a BAT. A large diameter cable could be a BAW. Consider that a large motor could be called a BAM. The list just goes on and on.

George, you need a BAH.

Just fun with words,

Ken

Re: Adjusting to Square

#12

Precision cutting

Lee Schierer - McKean, PA

>Measure with a micrometer, mark it with chalk and then allow a blind man with an ax to do the cutting!

Nice work so far George.

Lee

Re: Adjusting to Square

#13

Re: Precision cutting

paul Waddle

>My,my, all those spring clamps sure do make the shop look impressive! Give it a lick for me... pw

Re: Adjusting to Square

#14

And if you go to Memphis....

Tim Greif - West of Chicago

>Beale street in Memphis is the place to be to hear some great blues. Lots of vendors sell "Big-A$$-Beers" at sidewalk storefronts. Just seems to be a staple on Beale street. I like Memphis.

Re: Adjusting to Square

#15

OK, I give up, where's the beer?

Stephen Kirk in Quakertown, PA

>Colonel,

You aren't going soft on us, are you. I see beer in almost all of your pictures, and I looked pretty close on this one but I couldn't find any. I saw some evidence of heavy beer drinking, but no actual beer.

Re: Adjusting to Square

#16

BAPs, BABs and BAH'd!!!

Diane Farley

>Hey Uncle Gorgeous,

I think what you and Poopsie need are Big A$$ Pipes (BAPs), Big A$$ Beers (BABs)and then get BAH'd---BIG A$$ HAmmered!!!(Just watch out for the BATs--Big A$$ Termites!)

De

Re: Adjusting to Square

#17

Now De........

George@Colonel's Workshop-Havertown PA

>Your Dad and I already have everything we need: You! And maybe a few more Big A$$ Beers. We also have a great supply of Big A$$ Termites, AKA kids who are currently forming their own woodworking "splinter" groups.

Uncle Gorgeous