Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Sanding a Table down stained with Analine Dye

Posts

Sanding a Table down stained with Analine Dye

#1

Sanding a Table down stained with Analine Dye

Mark McC

>I made and finished a pair of end tables from Mahogany and then stained them a "reddish" tone using an aniline dye.

Thought the tone was right, but now that they are in the room with the other furniture, I wished I had made them from walnut or at least gone after a more chocolate brown mahogany tone.

Rather then build new tables, can I sand them back to bare and re stain or dye?

Just wondering if there is any risk or reason why I should not do this because it is an aniline dye stain versus other. Penetrates too deep,etc ????

I have never re-finished a dyed piece before.

Thanks

Mark

Re: Sanding a Table down stained with Analine Dye

#2

Re: Sanding a Table down stained with Analine Dye

Sue McLam in Orange, VT

>Mark,

I've done it several times (on maple, not on mahogany). There will be some dye left down deep in the pores, but it can be done. No tricks, just a lot of sanding.

Sue

Re: Sanding a Table down stained with Analine Dye

#3

Re: Sanding a Table down stained with Analine Dye

Thomas Skaggs, Foothills of Mount Level

>You can do that to a degree. The dye can sometimes penetrate to where it would take a lot of removal. Generally it's not hard to sand to where the dye is lighter. So just sand it to where the dye is lighter. At that point you can go over it with a browner dye and the new color will dominate.

Of course,make sure you do a test panel. Finish a panel just like the tables are now and remove the finish the same way and use to test.

And with dye, keep an eye that you sand all areas to an even amount of color removal so as to avoid light/dark areas.

Tom

Re: Sanding a Table down stained with Analine Dye

#4

Re: Easier, Maybe *LINK*

Mark Mandell - Gone Round In Jersey

>Rather than resanding and going through all of that, you should consider glazing or toning what you already have.

By glazing you add a bit of a scond color and then wipe off the excess. For instance wiping with General Finishes' Van Dyke Brown may give you enough of a color change to match your existing items. This is a waterbased glaze which will pick up your woods' pores if not already filled.

Second, you should consider toning your piece by adding a colorant to your finish. This is especially nice when spraying waterborne finishes as you can add dye concentrate easily and apply very light coats to build to the exact color you want, then apply a coat of clear. Oil finishes are most often toned with pigments.

I'd suggest you repost your question with a close-up picture of your piece on Jeff Jewitt's finishing forum at the link.


Finishing Forum

Re: Sanding a Table down stained with Analine Dye

#5

Re: Sanding a Table down stained with Analine Dye

Steve Schoene

>Once you have stripped the top coat. Try using chlorine bleach to lighten the dye. It will penetrate to a similar amount and get much of it.

This could be particularly important if you are trying to refinish factory furniture which may have bleached wood where too much sanding might reveal wood significantly darker than its neighboring boards.

Re: Sanding a Table down stained with Analine Dye

#6

Absolutely Use Chlorine Bleach After Finish is Rem

George@Colonel's Workshop-Havertown PA

>

Re: Sanding a Table down stained with Analine Dye

#7

Yes, chlorine bleach is used....

Howard Acheson

>... to remove dye stain. First remove the covering finish using a chemical paint remover. Follow the directions on the can. Give it a day before the next step.

Then use a fresh bottle of Clorox or other chlorine laundry bleach. Mix it 50/50 with distilled water and apply it with a sponge. Let it dry. If necessary, do it again. You should expect to end up with all the color gone.

The water will raise the grain so you can expect to do some sanding to flatten and smooth.

Trying to sand out a dye stain is a lot of work as the dye will have penetrated quite deeply.

Re: Sanding a Table down stained with Analine Dye

#8

Re: Easier, Maybe

Tony - Memphis

>There are several things I would try before trying to sand out the color. Glazing is an excellent choice. I've been amazed at how much I can manipulate color.

If that doesn't work and you remove the topcoat, I would try playing with using other colors of dye to change the color. I can't direct you (Jeff can), but there are color tricks like you may use a very green dye on top of your current color to get more brown. Its not intuitive, so I would ask Jeff. My wife, the artist, can explain the colro stuff better. When I stain mahogany, I start with the most hideous looking red color. It looks awful. I then add a brown mahogany color that gets me to the final color I want. Dyes are nice in that they don't muddy up the grain. Don't be surprised if Jeff suggests a plain primary color. I believe there have been some articles in FWW that show this. Maybe Mr. Dresdner will chime in . This subject may be in his book? With his experience in the string instrument biz, I'm sure he knows all about this subject.

Good luck with your project. Let us know what you decide so we can all learn something. We've all been where you are at.

Tony