Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Shop layout

Posts

Shop layout

#1

Shop layout

Shane S.

>I am setting up my shop (20' x 22') and was wandering if anyone had any thoughts on the layout of tools (bandsaw, drill press, shaper, etc) and work benches. I know this topic has come up before, but I couldn't find it in the search. Any thoughts or floor plan drawings would be appreciated. Thank you.

Shane

Re: Shop layout

#2

Re: Shop layout

steve mackay

>I pretty much let short ( as possible ) runs for the DC dictate the layout. But the bestest move I made was a corner style bench high enough for a bar stool and under a big window. Peg board over all within easy reach of the stool. I know most folks center around a center-shop bench but for everything but the work peice ( gear, tools & equipment ) this " sideboard " really gets it !

Re: Shop layout

#3

Re: Shop layout

Bill Howatt

>Make sure you have a minimum 8' infeed and outfeed distance on your TS since sheet goods and the most commonly used dimensional lumber is usually that size. If you plan on resawing with a bandsaw apply the same rule as the TS.

See if you can accommodate your jointer and other stationary tools along a wall since you don't have to get to both sides of it to make it work. Naturally, wall space isn't infinite either.

I find it is easy to say that I'll roll out the whatever when I want to use it, or haul it off a shelf and set it up. For me the reality is that if it isn't handy I'm likely not to use it. In other words, I try to have everything accessible and ready to use as possible.

Bill

Re: Shop layout

#4

Re: Shop layout

Scott in Montana

>Hello Shane,

I have a 20x22 shop with a tablesaw, a bandsaw, a shaper, a bench, a jointer and so on. No matter what the layout... trust me, you don't have an inch to spare. I have so little room anymore that I am restricted to making jewelery boxes. :O)

Well actually I've done pretty well considering the accumulation of power tools I have. One of the best things I did was to keep almost everything at the same height as my tablesaw; this aids in working with large panels and long boards. Having my jointer at the end of my tablesaw has also worked well. Upon ocassion I need to lay a big sheet on my tablesaw and if I remove the fence from my jointer its bed is level with my saw's extension table. My mitersaw/radial arm saw bench sits on the other end of my tablesaw and again it is at the same level as my tablesaw. My workbench is just an inch or two higher than my table saw and sits directly behind it. My shaper can pull double duty as part of the outfeed table for my tablesaw.

My stationary disc/belt sander, router table, bandsaw, drill press, mortiser,and Panamax sander all line up along the far wall. Thank God for mobile bases! My jointer and shaper are a European combination unit that I have really enjoyed.

There's not much room left on the walls as they are paneled with plywood and hand tools cover most every inch. I still need to build more cabinets to mount high on the walls. Moving out my huge rolling mechanic's toolchest and moving tools to the walls really freed up a lot of usable floor space.

Another appliance I couldn't live without is a thin vertical panel saw I made. Being able to slice up sheets of plywood to more handlable sizes is a real plus.

Another thing you might want to consider is painting the floor a light color to make the shop feel larger. Light colored floors also make finding that important dropped screw easier. And don't forget to plan out your lighting for good coverage.

It's a challenge but it can be done.

Good luck,

Scott

Re: Shop layout

#5

Correction:

Scott in Montana

>Make that Perfromax drum sander... not Panamax.

Re: Shop layout

#6

JL

Re: Shop layout

JL

>Grizzly has a shop layout tool on their website. It has "footprints" of their tools of course :). I used it when I did the layout for my shop. The graph paper alternative also works.

Re: Shop layout

#7

Re: Shop layout

Walt Turpening

>I have had a two car shop twice (current one counted), and the layout has not stayed the same as the initial set ups.

This time around one wall with no windows is my lumber rack (I rarely use sheet goods) with many many many small shelves so I am not having to go through lots of planks to get to the one I want. My planer and mortiser are on casters out of the way. The dust collector is in the corner near one of the garage doors making it easy to dump in a wheel barrow to the compost pile.

My assembly table is on casters and only 24 inches high. I put a melamine box on it to bring it up to the table saw height as an out feed. A rack under the assembly table holds 75% of my clamps (long monsters on the wall).

Table Saw is on an HTC base and nearly centered on a garage door to allow for longer than 8 foot rip and sheet goods. If I did more sheet work I would make a panel saw. The work bench (classic) is diagonal in front of the pegboard tool racks.

All walls are white. I have found there is never enough lighting so I use magnetic base lights at the bandsaw and drill press.

I am a chair maker.

Walt T.

Benches, Stools and Chairs

Re: Shop layout

#8

Re: Shop layout

Larry Clinton At Frankfort (Central)., Indiana

>I built my 30' X 30' shop about 4 years ago - still moving things. I finally put my major tools (Unisaw with extensions, MM 16 bandsaw, 20" planer, 12" lunchbox planer, 8" long bed joiner, Router table, Scroll saw and two roll around tool cabinets/ chests. I don't have mobile bases under my PM 90 lathe, Pm Drill press, 8" grinder, surface grinder, 60 gallon compressor, AC welder, workbench or bench with morticer, stationary belt/disk sander & wet grinder. I also have mobile shelves for storage of cutoffs and extra lumber and a mig welder and acetylene outfit on mobile bases. The real issue is that I use the shop for very different projects. My son & I are making all the trim for his house from White oak. This requires I have room to join, plane and saw boards up to 16' long. I have also built cabinets in the shop (and will be building more). This means I have to have room at the table saw for 4 X 8 sheet breakdown & room for assembly, glue-up & finishing. I just don't think I can arrange the tools permanently and have them functional for all projects. I have installed enough electrical outlets (120 & 240V) around the shop so I can move just about anything anywhere using short extension cords. I also installed extra 6" drops and use flex tubing for the dust collector system. Another issue is that I don't have a garage, so if we want to work on a vehicle I move the equipment aside to make room - Guess I will leave things this way as I can't come up with a better solution - don't have room or money to double my shop size :~).

Re: Shop layout

#9

Re: Shop layout

Robin Corell in Atascadero, CA

>I am a big fan of using graph paper for making scale layouts. I use a fine line shapie fot the tool and I use a yellow highlighter for the tools infeed and outfeed and tyhen cut that out. I tape enough sheets togetther to plot the shop wals on and then arange the 'furniture'/ When arranging I use a compas set to scale a 36" walkway betreen tools and then try to overlap as many yellow infeed and outfeeds areas as I can.

I usualy angle tools rather than having them all set up square to the walls. I find that I usually need to use a long diagonal of the rooom for the table saw. I am not a fan of mobile bases so the tools stay put, I usually set my bandsaw up with 6 feet or less of out feed room as this will acomodate 99% of what I do. I have it set up now so that I can move it about 6" and twist it and get a 10" board off it. I like the extra room for a walkway so I usually have it set up with less outfeed room.

the layout changes as my work dictates and as the tools change as I aquire new ones or upgrade old ones. a dust collector or electric can be changed to suit me rather than inconvienience me each time I want to use a poorly placed machine.

have fun with it and if you use graph paper save your scaled tools in a file folder for future rearanging DAMHIKT.

Robin

Re: Shop layout

#10

Re: Shop layout

Barry Irby

>I have a small shop, about 13 by 22. Its a one car garage. I have the TS centred on the garage door and the blade is i6' from the back wall so that I can open the overhead door and rip a piece 16" long. That make it about 6" from the door when its closed. About ninety nine percent of the time that's enough, but I can open the door when necessary. The "People" door into the shop comes through the long wall. My jointer is lined up with it so that if necessary I can open that door and steal a little room out of the room next door.

My shaper, chop saw and RAS are lined up down the wall with the door and share a common fence. The top of the fence on the jointer serves as a prop for the RAS when the pieces are long.

My lunch box planer is on a mobile base and set up to allow a piece to start under a workbench and exit under the wing of the TS. The bandsaw work passes above most other things.

The point is that in a small shop you have to think in three dimensions. I would suggest that you set up the scale drawing suggested by others and then make a scale model of a long board and wide board and a sheet of plywood. Then visualize the work you might do and see what happens when you pass that board over your machines.

I scheming on making a cart for my planer that allows me to flip it upside down when not in use. This would allow it to serve as a place to put my turning tools when I am using them. Also, when up-right, it would be the same height as the table on the bandsaw so it could serve as a outfeed table. Some things have to do double or triple duty in a small shop.

Re: Shop layout

#11

Re: Shop layout

Ed Mulligan, Cape Cod

>Put everything on casters or mobile bases.

One thing that is often missing from small shop layouts on graph paper: an assembly area where you can walk around the work, apply clamps, sand etc. With larger pieces it is a lot easier to walk around them then to move them for access.

When it's time to assemble (or finish), roll the big machines into a corner and create your work space.

Ed

Re: Shop layout

#12

Re: Shop layout

Jay Lombardo

>Shane, there is a Shareware/Freeware program that is pretty simple and fun to use. It will allow you to move the tool icons all around the shop. Here is a link to a site where you can download it.

http://www.inthewoodshop.org/software/x9r7y5.zip

Good luck,

Jay

Re: Shop layout

#13

Re: Shop layout

Lloyd

>I am planning a new workshop too. I can go 12-14'x 22" also. Everyone had great ideas. I now see I better make the width 14'. I like the idea mention about making the assembly table mobile, also like the table top extending past the base, to use for deep clamps. One more idea that I like is to place the drill press on the out feed side of the band saw. Then you can clamp a board on the drill press table and raise its height to just under the saw table.

Just a though to ponder.

Re: Shop layout

#14

Re: Shop layout

Shane S.

>Thanks for your replies. I think these tips will help out a lot.

Thanks again,

Shane