Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Question about Finishing

Posts

Question about Finishing

#1

Question about Finishing

Cody Lewis in LV

>Here I come with another rookie question: If I'm doing a project that has hidden places (like inside a bed-side table where the drawer slides in and out) should I apply polyurethane finish to those areas? I didn't stain those areas because there was no need - they'll never be seen - but I'm wondering if the finish coat is good because it seals things off and perhaps minimizes swelling/flexing over time???

Re: Question about Finishing

#2

JL

Re: Question about Finishing

JL

>A good sealer coat doesn't hurt - and it keeps down "dust collection" and soiling. A nice spray or wipe-on lacquer coat is what I have used rather than poly.

Re: Question about Finishing

#3

I would avoid poly on the inside of anything. Use

henthorn

>shellac instead. You will be happier.

Re: Question about Finishing

#4

Re: Question about Finishing

Jim Dillon

>Cody,

Not a rookie question at all. To me, it depends how much "extra" work you want to put in. Once assembled, the insides are often difficult to get to, difficult to apply an even coat of whatever, and difficult to wipe up any excess finish if necessary. Nevertheless, a wipe-on coat of 1# pale shellac or wipe-on poly is easy to apply and will protect the interior and give it a more finished look IMHO, even if it will be only you who will know. My 2 cents.

Jim

Re: Question about Finishing

#5

Re: I would avoid poly on the inside of anything.

Cody Lewis in LV

>I've had several people tell me they prefer shellac to poly. Since I've always used poly, I gravitate to it, but I'd be curious to know why so many prefer shellac.

Re: Question about Finishing

#6

Re: I would avoid poly on the inside of anything.

Bruce, a MN Galoot

>I prefer shellac for "inside" work because it dries very fast, very hard, and it never softens. It also doesn't smell.

Bruce

Re: Question about Finishing

#7

Re: Question about Finishing

Ed Mulligan, Cape Cod

>Cody -

When an oil base finish is applied to an enclosed area like the inside of a chest, it emits a foul odor for a long time (years). Anything stored in the space absorbs the foul odor.

If you intend to finish the inside of your project, use something that is not oil-based to avoid the odor problem. Shellac is a good choice. Solvent or water base lacquer is good. Haven't heard anything about water-base poly for enclosed spaces but I'd avoid it until a definitive answer emerges.

Ed

Re: Question about Finishing

#8

Lee Grindinger

Here's the reason- "It also doesn't smell"

Lee Grindinger

>Shellac's alcohol leaves quickly and leaves behind little odor. Poly and other varnishes leave an odor that can last for years.

Lee

Re: Question about Finishing

#9

Ellis Walentine

To finish or not

Ellis Walentine

>Personally, I don't think you need to finish the inside of a carcase. Historically, I suspect the majority of case pieces were left unfinished inside. The shrink/swell/movement factor is not likely to be an issue on a small piece like a bedside table, whereas it might be if this were a large case piece with solid wood sides.

If you do decide to put a light finish in there, use something that won't keep outgassing rancid oil smells forever. Shellac is the most time-honored alternative, but lacquer and waterborne coatings are also relatively odor-free after they have fully cured. And, regardless of whether you finish the inside, I'd finish the underside of the top before assembly to keep the moisture transfer rate similar on both sides. This will reduce the tendency to cup with changes in relative humidity.

Ellis Walentine, Host