Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Emglo compressor problem

Posts

Emglo compressor problem

#1

Emglo compressor problem

Scott Burr in somewhat warn Ben Lomond, CA

>Hi All, My Emglo twin tank compressor desided it didn't want to start today. The piston isin't moving it seems. The motor starts but it blows it's breaker. Oil lever is fine, the filter was a bit dirty, well really dirty. It's around 7 years old. Is there a easy fix or do I need to take it to a service center?

Thanks, Scott

BTW there seems to be a lot of Scotts hanging out here...

Re: Emglo compressor problem

#2

Re: Emglo compressor problem

Jim Dillon

>Scott,

I purchased an Emglo "hot-dog" compressor about 10 years ago. I checked the oil level religiously every month or so for the next 5 years and patted myself on the back each time. The oil level never dropped so I thought I was OK. Well, suddenly the compressor began to start with difficulty, then wouldn't start al all. Checked the oil level and it was just fine. Decided to change the oil "just in case". What do you know! It started right up. The same thing happened again about 2 years later (I'm a slow learner 8-)). Now I change the oil on a more regular basis. Just a guess, but try changing the oil and pressing the thermal reset switch.

Jim

Re: Emglo compressor problem

#3

Thanks Jim!

Scott Burr in somewhat warn Ben Lomond, CA

>The oil in mine has never been changed. Guess it's about time to try replaceing the oil in it.

Is it something I can get at the loco lumberyard where I purchased it?

Ya think more people would own these and would have chimmed in seeing how popular their are...

Thanks again, Scott

Re: Emglo compressor problem

#4

Re: Thanks Jim!

Jim Dillon

>Scott,

I think the Emglo manual recommends regular 30 weight oil low detergent available from any auto parts store. That is what I've used. Mark Mandell (a frequent contributor to WC) alerted me to the availability of a synthetic air compressor oil as well. The first time I changed the oil, I added fresh oil then ran the compressor (after much relief that it started) for a few minutes. I then changed the oil again. My thinking was that I was flushing out even more of the old oil. You don't need much oil per change - maybe 3/4 cup or so. Hope changing the oil does the trick for you.

Jim

Re: Emglo compressor problem

#5

Jim & Scott

Mark Mandell - Gone Round In Jersey

>The synthetic compressor oil [Ingersol-Rand's "Select" or equivilent] will largely eliminate carbonizing of your pump's valves, piston and rings (resulting from petroleum oils), but it still should be changed every a year. Remember, aiir compressors don't have oil filters so any dust etc. that gets through the intake filter (you DO change that as well right?) will wind up in the oil pan along with condensed moisture. That will do nothing but increase wear on your compressor's moving parts if you don't drain and change on a regular basis. The 1 year interval is based on average homeowner use. Higher use means changing the oil more often.

Re: Emglo compressor problem

#6

Filter? What filter?? 8-) 8-)

Jim Dillon

>

Re: Emglo compressor problem

#7

Yep Mark, My filter is filthy...

Scott Burr in Ben Lomond CA

>Havn't changed the oil it once sence I bought it. Looks like I'm off to get a filter and oil. Then cross my fingers!

Thanks for your help!

Re: Emglo compressor problem

#8

When you get back

Mark Mandell - Gone Round In Jersey

>After you change your oil (and filter),

drain your air tank (first time in how long?) and leave it open BEFORE you try to start your motor. That will eliminate any back pressure on your pump and give the the best chance of getting it to turn over and run. If you get it started, I'd suggest to let run without pressure for about 15-20 minutes, and then drain and change your oil again, as you're liable to get a bunch of junk flushed out that way.

good luck {but keep the service guy's number handy]

Re: Emglo compressor problem

#9

You guys rock! IT'S ALIVE!!!!!!!!!!!!!!!!!!!!!!!!!

Scott Burr in somewhat warn Ben Lomond, CA

>Thanks so much guy's!

I just changed the oil twice once to flush out after running it for a bit. The old stuff that came out of it flowed like molasses and was a dark as a moon-less night.

Slapped the new filter on it and BINGO!

Mark, I keep it empty most of the time so it does start, it get quite cold here and in my shop, so I drain the air before trying to fire it up.

Thanks for you response fellow transplanted ponder 8^)

THANK YOU GUYS!

BTW, The service guy was the one I went to get the oil and filter from.

Re: Emglo compressor problem

#10

That's great. Glad it worked!

Jim Dillon

>

Re: Emglo compressor problem

#11

Good Save!!

Mark Mandell - Gone Round In Jersey

>Don't wait so long for the next change, eh?

Glad it worked out.

Re: Emglo compressor problem

#12

No I won't, but....

Scott Burr in somewhat warn Ben Lomond, CA

>I bought it at a tent sale, never got a manual for it so, I'll admit I'm a bit dumb about care and feeding. Thanks for the parental lession Mark!

Care and feeding is now on schedule!

Thanks again for all your help!

Re: Emglo compressor problem

#13

Seek *LINK*

Mark Mandell - Gone Round In Jersey

>Your model's destruction manual at the link. Click "cancel" when it asks you to sign in. The model # should be on the nameplate, but if that's gone, click on the site products and find the compressor that looks closest to what you have. Care & feeding is going to be substantially identical.


DW-Manuals