Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Steam bending

Posts

Steam bending

#1

Steam bending

JerryBurns

>I am looking for information on steam bending. I will be building a set of Morris chairs and I was thinking about makeing the arm rest in a bow. Has anyone made a steam bending box? I remember reading something about it but i do not recall the magazine that I read the story in. I have Woodsmith #155 with a bent arm but is it not a curve

and I want to use a curve.Next question does the type of wood matter

I am taking inventory of the wood I have on hand and I might have enough cherry to build one out of cherry.and one out of QS white oak

I will post a picture when I finsh one (some time this summer )

Re: Steam bending

#2

LV steam bending info *LINK*

Charles R. Smith

>You might start by downloading and reading this instruction booklet from Lee Valley. While it was written to be used in conjunction with their steam-bending products, as is typical of LV's technical bulletins, you can learn a lot from it. Hope that helps.

Charles


Lee Valley's instruction booklet

Re: Steam bending

#3

Re: Steam bending

Bruce, a MN Galoot

>You could easily laminate that arm, using laminates about 1/8" thick and have zero problems with spring back.

Bruce

Re: Steam bending

#4

Re: Steam bending *LINK*

Dave Mount

>Getting set up to steam bend is easy. Your box doesn't need to be anything more than some boards nailed together, sized for what you are steaming. For the steam part, I use a Coleman stove with a cheap closed teapot, pulled the whistler off the pot and connected it to the steambox with radiator hose. I also put some cross dowels in the steambox to suspect the work so steam gets to all sides.

For something like the arm of a Morris chair, you may want a more powerful heat source and a larger boiler. It is very important that you do not run out of water partway through, or you have to start over (you lose the heat while the added water is coming up to boil).

Good old rec.woodworking had a FAQ that has some useful info, link below.

Best,

Dave


rec.woodworking steambending FAQ

Re: Steam bending

#5

Re: Steam bending

Moses Yoder in White Pigeon, MI

>Jim Shaver built a set of Morris chairs a few years back and posted a nice write up on it; I think they might even be in shop shots (found it at http://www.woodcentral.com/shots/shot688.shtml). I think if you searched for threads on these chairs you would find quite a few discussions. It would be worth your time to read it. If I remember correctly he used an arm that was angled by adding a piece at the front bottom of the arm. Hard to describe but I recently read an article on it in an old FWW because a Morris chair is one of my next projects. I liked the look of the angled arm versus bent, probably more comfortable to sit in and a little bit easier than bending. Steam bending is easy; everything you need to know is in the previous posts. The main variable is the amount of spring back. Make sure you have plenty of steam and just do it.

Re: Steam bending

#6

Re: Steam bending

Jim Hoeller

>I have used a Wagner wallpaper steamer with good results. The $50 version provides enough steam for about two hours. I made a steam box from one 10 foot 2x6 and one 10 foot 2x4. both were cut down to 5 feet. I caulked the seams with silicone caulk and screwed the boards together. The box had inside dimentions of about 3 1/2" x 2". One end was closed; the other had a hinged door that closed with a loose bunge. The hose from the steamer was inserted in a hole drilled in the bottom of the box. Dowels to rest the parts to be bent were inserted about every 10 inches or so. Do not close the steam box tightly and do allow for condensate to drain out.