Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

building a cradle with cherry (planing & joinery)

Posts

building a cradle with cherry (planing & joinery)

#1

building a cradle with cherry (planing & joinery)

MN deepwoods (Dave)

>Greetings friends. I'm building a cradle for my buddy's first child from some cherry boards, 3/4" I believe. The wood is in his dad's shed. Two questions: 1) is it best to fasten the boards to desired width then run through planer down to 1/2" thickness, or plane down THEN join together?

2)Dowels or Biscuits? I have both a biscuit joiner and doweling jig so can do either. The cradle is mobile and fastens into a stand which looks somewhat like a quilt rack. The wider pieces will be at the head and foot of the child. Is it obvious yet that I have no children and have never used a cradle? :-)

Re: building a cradle with cherry (planing & joinery)

#2

Re: building a cradle with cherry (planing & joine

Barry Irby

>If your planer is large enough, glue up the pieces first and then plane them.

You can plane them first and then glue them up, but I find it difficult to keep them perfectly flush with each other and end up planing or sanding them even thinner.

1/2" is probably too thin for biscuits. Biscuits tend to swell in the joints and may puff up the surface if the stock is thin. If you sue them, wait as long as you can (couple of weeks) for the glue to fully dry and the biscuit to dry and stabilize, before you sand or plane. Otherwise, you sand the little bulge above the biscuit off and then it shrinks and you may end up with a slight but visible depression.

Truth be told, for long grain edge joints you don't need biscuits or dowels. Good glue joints are stronger than the wood and don't need any reinforcement. You can use either, but they add almost nothing to the finished product.

Re: building a cradle with cherry (planing & joinery)

#3

Re: building a cradle with cherry (planing & joine

Robert R Clough - Thorncraft

>Barry is correct - there is no need for a "belt and suspenders" as glue is fine by itself. What kind of a cradle? Slat or solid sides? What dimensions? I gather you are asking here about the head and foot pieces? Have you a rough drawing you could post?

Re: building a cradle with cherry (planing & joinery)

#4

Re: building a cradle with cherry (planing & joine

David Yoho

>1) is it best to fasten the boards to desired width then run through planer down to 1/2" thickness, or plane down THEN join together?

The problem I've seen when gluing boards together first and running through a planer is them not being flat because the boards shifted a little when clamped. There are ways to deal with this before planing but if you don't you won't get flat results. That's why I usually plane to thickness and then join them. Care at glue-up and even the use of cauls to keep the panel flat will yield good results. A cabinet scraper is good to flatten any difference at the joints once dry.

2)Dowels or Biscuits?

Neither! Today's glues are plenty strong. For alignment, depend on being careful at glue-up. Again, using wooden cauls separated from the panel with wax paper and clamped will keep the panel flat enough.

Re: building a cradle with cherry (planing & joinery)

#5

Re: building a cradle with cherry (planing & joine

Joseph Mulherin

>Dave, I have made four cradles earlier in my life. I bought plans from www.furnituredesigns.com located in Illinois. I would just use glue to meld the boards together, and if the planer is wide enough you can run the boards thru nicely. I would not go any lower than 3/4" on anything, and if the design is like mine I would just glue up boards so you can get the 1 1/2 - 2" stantions

Re: building a cradle with cherry (planing & joinery)

#6

Re: building a cradle with cherry (planing & joine

MN deepwoods (Dave)

>Robert,

The plan is one my buddy's uncle had made. He had attached the paper plan to a piece of hardboard. As it turns out it is from Wood Magazine and is on the cover of that issue. It may be Nov '07 or Oct?. I can't find my copy right now. I'll post a picture when we finish it.

Regards,

Dave