Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

OT replacing wear strip on aluminum snow shovel

Posts

OT replacing wear strip on aluminum snow shovel

#1

OT replacing wear strip on aluminum snow shovel

Tim Greif - West of Chicago

>I've never been able to find a suitable way to renew an aluminum snow shovel after the steel wear strip and rivets have worn down. Always seemed silly to throw away a perfectly good shovel because of a worn out or dislodged wear strip. Any northerners have any suggestions. I'm gettin tired of shoveling here - west of Chicago.

Re: OT replacing wear strip on aluminum snow shovel

#2

Re: OT replacing wear strip on aluminum snow shove

Rick in Colgate, Wi

>Our shovels are certainly getting a workout this winter!

I've replaced mine numerous times. I get a piece of flat stock 1/8" X 1" and long enough to cover the width of the shovel. Drill out the old rivets, drill new holes in the new wear strip to match the holes in the shovel and attach using pop rivets. I do use washers on the end of the rivets when I insall them.

Re: OT replacing wear strip on aluminum snow shovel

#3

Re: OT replacing wear strip on aluminum snow shove

Chuck Lenz

>Some hardware stores carry the wear strips, the one I use to work at did.

Re: OT replacing wear strip on aluminum snow shovel

#4

Re: OT replacing wear strip on aluminum snow shove

Jay in TX

>Hmmm... Since repair is the only option.

What exactly is dislodged? I'll assume it affects performance to not be able to use the shovel.

So,

1. Use hand-drill to remove current rivets (drill with bit that will remove the center without widening the holes).

2. Find suitable (Length, width, thickness) piece of scrap metal (probably mild steel) and fit to empty spot where wear plate used to be. You may be able to use the old wear strip to mark fastner holes for new wear strip.

3. After marking new wear strip for holes, drill them out (probably best to use the Drill Press for this) Remember you are drilling metal, not wood.

4. Fit check new piece to shovel, make adjustments if necessary

5. Fasten new wear plate to shovel using rivets or some other appropriate fastener that won't interfere with normal operations.

BTW, I've never repaired one. I've either replaced or used an old 'coal' shovel that I got from Dad(don't know if coal is right, but its big) and bought a replacement near the end of the season. And no, I'm not originally from Texas. But the mild winters have been almost as pleasant and the allergies have been unpleasant.

Re: OT replacing wear strip on aluminum snow shovel

#6

You use them to fill dumpsters after hurricanes

Bill Howatt

>

Re: OT replacing wear strip on aluminum snow shovel

#8

Delrin

Tom Dunlap

>After using Delrin for some skids on a tub that I towed behind my atv I've used it for other wear strips. Super tough, lightweight and easy to work.

I also found some sheets of plastic,not sure of what it is, that came from an outdoor storefront sign. A buddy who does sign work told me that the stuff will not break if a rock is chucked at it at minus 20. The sheet Ihave is about 3/16" thick. If you want a chunk, email me and I can mail a life time supply of wear strips to you.

Tom

Re: OT replacing wear strip on aluminum snow shovel

#9

Re: Don't you mean a front end loader?

Brian in Brighton

>

Re: OT replacing wear strip on aluminum snow shovel

#10

Re: Delrin

Frank Orfanello

>Can Delrin be cut and drilled with ordinary tools?

Re: OT replacing wear strip on aluminum snow shovel

#11

Good for sawdust

John K Jordan

>

Re: OT replacing wear strip on aluminum snow shovel

#12

Re: Delrin

Bob Entwisle in NJ

>Delrin is pretty easy to work with both hand and power woodworking tools.