Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Rubbing a finish out.

Posts

Rubbing a finish out.

#1

Rubbing a finish out.

Lee Beeden

>I've just finished putting the first coat of Varathane Dimond oil based finish on my cabinet doors.

This morning I noticed there are a few bubbles in the finish.

I did tack cloth everything last night but it is possible these bits are dust as well as air bubbles, I was careful not to shake but stir the finish.

I'm curious whats the best strategy for rubbing these out?

All comments appreciated.

Lee

Re: Rubbing a finish out.

#2

Re: Rubbing a finish out.

Dick Coers

>I like to use 320 grit sandpaper to cut off the bump or bubble. If you use synthetic steel wool it will polish over the bump and not level it out. Make sure the sandpaper is compatible with water base. Some sandpaper has sterates to keep it from clogging. The sterates are soap and maybe the water base will not stick to it.

Re: Rubbing a finish out.

#3

stearates and sandpaper

John K Jordan

>>...Some sandpaper has sterates to keep it from clogging.

>The sterates are soap and maybe the water base will not stick to it.

Perhaps you or some other wizard can explain this further. I've always wondered exactly what stearated sandpaper was treated with and how this helped. I looked up "stearate" and found the chemical definitions (flexible hydrocarbon chain, anion (salts and esters) of stearic acid) and uses, namely that soap/detergent consisted of sodium or potassium stearate while other metal stearates (aluminum, lithium, calcium, barium, etc) were used as hardeners, softeners, gelling agents, parting compounds, and lubricants in a huge variety of products from candles to medicines to fireworks.

Several sources indicated zinc stearate is the dry lubricant commonly used on sandpaper. Some sandpapers feel a little waxy to me - is that the zinc stearate lubricant I feel?

Ms. Wikipedia indicates zinc stearate "is a soap that repels water" insoluble in alcohol but soluble in aromatic hydrocarbons.

Does this zinc stearate simply coat the abrasive grains to help keep wood particles and saps from sticking between the grains? Is this coating tough or does it wear off easily with use?

JKJ

Re: Rubbing a finish out.

#4

Re: Rubbing a finish out.

Lee Beeden

>With regards to the sandpaper, when you say 'make sure it is compatible with water base', are you thinking i am using a water base finish for a top coat?

I have a bunch of old sandpaper that i use on the orbital sander, will this do?

thanks

Lee

Re: Rubbing a finish out.

#5

Re: Rubbing a finish out.

Dick Coers

>I guess I stopped reading at the diamond part of the finish. Darn it. I tried Varathane Diamond water based finish years ago. As Emily Latilla used to say "That's something completely different, never mind." I still recommend sandpaper between coats for the same reason I mentioned.

Now if you were using water base, here's the reference on the sandpaper.

From the Target Finishes web site;

Sand surface to be finished with quality, stearate-free sandpaper. The sandpaper grit schedule will vary between 220 to 400-grit depending on the surface condition and type of wood being finished.

After the surface has been sanded and prepared, remove dust with a water-damped, lint-free cloth. DO NOT USE OIL/WAX TACK CLOTHES.

Re: Rubbing a finish out.

#6

Re: stearates and sandpaper

Larry Clinton At Frankfort (Central)., Indiana

>Perhaps you or some other wizard can explain this further. I've always wondered exactly what stearated sandpaper was treated with and how this helped. I looked up "stearate" and found the chemical definitions (flexible hydrocarbon chain, anion (salts and esters) of stearic acid) and uses, namely that soap/detergent consisted of sodium or potassium stearate while other metal stearates (aluminum, lithium, calcium, barium, etc) were used as hardeners, softeners, gelling agents, parting compounds, and lubricants in a huge variety of products from candles to medicines to fireworks.

Several sources indicated zinc stearate is the dry lubricant commonly used on sandpaper. Some sandpapers feel a little waxy to me - is that the zinc stearate lubricant I feel?

Yes - zinc stearate is a dry lubricant -looks quite like flour. Where I worked before retirement, we used it in fairly large quantities (tons a month at one time). We used in in producing the carbon film for the old radio/tv controls (volume, color, vert. horz. etc). I have also mixed it in other lubricants as it has a very good characteristic that enables it to stay in place under high pressure. The zinc stearate used to coat sandpaper does prevent the wood rosin from sticking to the abrasive and the coating that holds the abrasive.

Ms. Wikipedia indicates zinc stearate "is a soap that repels water" insoluble in alcohol but soluble in aromatic hydrocarbons.

TRUE

Does this zinc stearate simply coat the abrasive grains to help keep wood particles and saps from sticking between the grains? Is this coating tough or does it wear off easily with use?

The stearate coats both the abrasive and (mainly) the binding agent that holds the abrasive to the paper or cloth backing material. This prevents the rosin and wood particles from sticking to these. I am not sure but would believe the stearate would wear off somewhat quickly from the abrasive, but enough remains on the backing to retard sticking. Almost (if not all) abrasives used for sanding wood are "open coat" which means there is openings between the abrasive grains for wood derbies to enter - allowing the abrasives to keep cutting. The zinc stearate prevents this derbies from sticking to the material - allowing it to fall away when you lift the sand paper from the surface (or strike it against your hand to clean it).

Re: Rubbing a finish out.

#7

Re: Rubbing a finish out.

Mark Mandell - Gone Round In Jersey

>Lee,

I would anticipate that what you have are dust nubbies rather than air bubbles.

I take it you want to level your film which you should do gently by hand with a block wrapped with the black wet/dry paper (320 or higher) with lubrication moving in the direction of the grain only. I use a hard rubber block.

Now a question: Do you want to recoat, or rub to final gloss?

Once you have leveled the film, wipe your surface well with paper towels and then a lint free cloth moistened with the lubricant you used (water or mineral spirits) to remove all of the sanding slurry. You can apply another coat of finish if you want more visual depth, or proceed to rub out the finish.

To rub out, start by wet sanding again with 800 grit w/d paper, again in the grain direction, and wipe dry. Next dry rub (same direction) with 0000 steelwool. Vacuum well.

SPECIAL NOTE: If you will be recoating, especially with a water-based or waterborne finish, NEVER, use steel wool. It will imbed metal fibers in the wood or grain which will either react with woor tannins or rust in the finish (or both). Use the synthetic pad material instead.

Now you can start the real rubbing. I like to use Meguires auto compounds starting with #2 Fine Cut cleaner, then #3 Machine Glaze, and if you want a float glass finish, #9 Swirl Remover. The good news is you can apply the Meguires with a power buffer; I use my RO sander fitted with a sponge head, a car waxer with also do nicely.

You can also use the more traditional rubbing compounds of powdered pumice followed by rottenstone along with a non-drying oil lube like mineral oil or "rubbing" oil. You can do these by power or by hand using a block wrapped with cloth that you change when you change grits.

Hope this helps.

Re: Rubbing a finish out.

#8

Stearates and waterbornes

Michael Dresdner

>Larry did an excellent job of explaining both how zinc stearate is applied to sandpaper and what it does. The problem is compatibility with waterbased coatings. Here's the story, and the solution.

Because zinc stearate is a soft, soapy material and because some tends to remain behind after sanding, it can create areas of lower surface energy. That means a high surface tension coating, such as waterbased finish, can develop fisheyes because of the presence of the stearate. One solution is to carefully remove all dust and residue with a damp cloth, but there is another.

When this first became obvious, the sandpaper designers went back to the lab and created stearated paper that does NOT shed particles onto the finish. Although it is stearated, it looks quite different. Instead of being dusty gray, it is gold colored with no free dust shedding off it. Use this gold stearated paper, formulated specifically for sanding between coats of waterbased coatings, and the problems will go away.

What is different about it? To picture stearated paper, imagine a donut covered in powdered sugar. To picture gold stearated paper, imagine a glazed donut. Both have sugar coating, but one sheds its powdered sugar more easily.